Lauterbach MMDSP Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 36

Lauterbach MMDSP Скачать руководство пользователя страница 18

MMDSP Debugger

18

©1989-2019 Lauterbach GmbH

SYStem.CONFIG.CORE

Assign core to TRACE32 instance

Default

coreindex

: depends on the CPU, usually 1. for generic chips

Default

chipindex

: derived from CORE= parameter of the configuration file (config.t32). The CORE

parameter is defined according to the start order of the GUI in T32Start with ascending values.

To provide proper interaction between different parts of the debugger the systems topology must be mapped
to the debuggers topology model. The debugger model abstracts chips and sub-cores of these chips. Every
GUI must be connect to one unused core entry in the debugger topology model. Once the

is

selected a generic chip or none generic chip is created at the default

chipindex.

None Generic Chips

None generic chips have a fixed amount of sub-cores with a fixed CPU type.

First all cores have successive chip numbers at their GUIs. Therefore you have to assign the coreindex and
the chipindex for every core. Usually the debugger does not need further information to access cores in
none generic chips, once the setup is correct.

Generic Chips

Generic chips can accommodate an arbitrary amount of sub-cores. The debugger still needs information
how to connect to the individual cores e.g. by setting the JTAG chain coordinates.

Start-up Process

The debug system must not have an invalid state where a GUI is connected to a wrong core type of a none
generic chip, two GUI are connected to the same coordinate or a GUI is not connected to a core. The initial
state of the system is value since every new GUI uses a new

chipindex

according to its CORE= parameter

of the configuration file (config.t32). If the system contains fewer chips than initially assumed, the chips must
be merged by calling

SYStem.CONFIG.CORE

.

Format:

SYStem.CONFIG.CORE

<coreindex>

<chipindex>

SYStem.MultiCore.CORE

<coreindex>

<chipindex>

(deprecated)

<chipindex>

:

1

…

i

<coreindex>

:

1

…

k

«
...
16
17
18
19
20
...
»

Содержание MMDSP





































Отзывы:

Нет отзывов