background image

LAUNCH

 

 

                                                

               TLT632AF INSTALLATION MANUAL 

 

                                                  6 

Under  normal  working conditions, equalization valves (8) 

and emergency lowering valves (9) are closed. Oil flows to 

the lower chamber  of  master  cylinder through check valve 

and  the force of the piston causes  the oil in the  upper 

chamber of the master cylinder to flow to the slave cylinder,   

so the two platforms go up equally. The flow of oil from check 

valve to the slave cylinder is blocked by equalization valves 

(8). 

For emergency lowering, open 2 emergency lowering valves 

(9) to lower the lift slowly and carefully. The lowering speed 

can be adjusted by speed valve (11). 

To equalize two platforms, open 2 equalization valves (8), 

raise the lift up and down 1 or 2 times and firmly closed 

valves (8). 

 

2.5 

Hydraulic Components 

in  Control Desk 

8

2

6

4

7

5

3

1

9

 
 

                             
                             
                             
                             
                             
                             
               
 
 

 

 

 

Fig.5 

3 Tools

 

Please get the following tools 

ready for installation:

 

Tools 

Specifications 

Level Bar 

L=400mm

15.7

″)

 

Chalk Line 

10mm

0.4

″)

 

Taper Plunger Chip 

 

Hammer 

1.5 kg(3 lb) 

Crescent Wrench 

40mm

1.6

″)

 

Open end Wrench Set 

11mm-23mm

0.43

-0.9

″)

 

Allen Wrench Set 

2mm-12mm 

Screwdriver 

150mm

5.9

″)

 

Rotary Hammer Drill 

20mm

0.8

″)

 

Hard Alloy Drill Bit 

Φ17mm

0.7

″)

 

Frame Level

JB3239-83

  L*W*H

300mm

×

40mm

×

300mm(11.8

×

0.16

″×

11.8

 

Содержание TLT632AF
















Отзывы: