background image

ii

LAUNCH

                                                             

Professional 129E User Manual

General Notice

• 

Other product names used herein are for identification purposes only and 
may be trademarks of their respective owners. LAUNCH disclaims any and all 
rights in those marks. 

• 

There  is  a  possibility  that  this  unit  is  inapplicable  to  some  of  the  vehicle 
models or systems listed in the diagnosis section due to different countries, 
areas, and/or years. Do not hesitate to contact LAUNCH if you come across 

such questions. We are to help you solve the problem as soon as possible.

Disclaimer

• 

To take full advantage of the unit, you should be familiar with the engine.

•  All information, illustrations, and specifications contained in this manual are 

based on the latest information available at the time of publication. The right 
is reserved to make change at any time without notice.

•  Neither LAUNCH nor its affiliates shall be liable to the purchaser of this unit 

or third parties for damages, losses, costs or expenses incurred by purchaser 

or  third  parties  as  a  result  of:  accident,  misuse,  or  abuse  of  this  unit,  or 
unauthorized modifications, repairs, or alterations to this unit, or failure to 
strictly comply with LAUNCH operating and maintenance instructions. 

• 

LAUNCH shall not be liable for any damages or problems arising from the 
use of any options or any consumable products other than those designated 

as Original LAUNCH Products or LAUNCH Approved Products by LAUNCH. 

Safety Precautions and Warnings

To prevent personal injury or damage to vehicles and/or this tool, please read 

this user’s manual first carefully and observe the following safety precautions at 

a minimum whenever working on a vehicle:

• 

Always perform automotive testing in a safe environment.

• 

Do  not  attempt  to  operate  or  observe  the  tool  while  driving  a  vehicle. 
Operating or observing the tool will cause driver distraction and could cause a 
fatal accident.

•  Wear safety eye protection that meets ANSI standards.
•  Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or 

hot engine parts.

•  Operate  the  vehicle  in  a  well-ventilated  work  area:  Exhaust  gases  are 

poisonous.

•  Put blocks in front of the drive wheels and never leave the vehicle unattended 

while running tests.

Содержание Creader Professional CRP129E




































Отзывы: