3
3. System Type
– Select your chosen heating system and enter
correct wattage you have connected. Wattage ratings of the heaters can
be found in the heater manual or online at laticrete.com.
4. Set time
– Manually set time.
5. Set date
– Manually set date.
6. Set daylight savings
– Set Europe, N.America, Australia or
switch off.
7. Temperature format
– Set the format as degrees Celsius or
Fahrenheit.
8. Home screen style
– Set your home screen style.
9. Background image
– Set your background style.
10. Display brightness
– Set the display and standby brightness.
11. Audio feedback
– To turn the touch sounds when making a
selection ON/OFF.
12. Heating target
– Control the heating via air or floor sensor.
13. Heating limits
– Delicate floor coverings such as vinyl, carpet
and laminate must be limited to 81
°
F (27
°
C). Tile floors can be set to a
maximum of 104
°
F (40
°
C).
14. Cost setting
– Select the rate you are on with your energy
provider and enter cost per kWh.
15. Program setting
– Select a preset program, set a fixed
temperature or set your own custom program.
16. Setback temperature
– The setback temperature is the
temperature you set for periods where you would like a lower
temperature or no heating.
NOTE: If the STRATA_HEAT™ Wi-Fi Thermostat is not
connected to Wi-Fi and registered on mystrataheat.com
you will not be able to control your heating using the app
or webpage.
IMPORTANT NOTICES
FCC Notice
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning:
Changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio TV technician for help.
Caution:
To maintain compliance with the RF exposure guidelines, place
the unit at least 8" (20 cm) from nearby persons.
IC Statement
This device complies with Industry Canada Licence-exempt RSS-247.
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that
TECHNICAL SPECIFICATIONS
Supply Voltage
120-240V, AC +10% / -15%, 60Hz
Maximum Switch Load
15A
Note: This product is not designed to be used with any inductive load
GFCI
Class A GFCI with 5mA trip level
Temperature Display Range
+32
°
F to 122
°
F (0
°
C to +50
°
C)
Operating Temperature
+32
°
F to 104
°
F (0
°
C to 40
°
C)
Storage Temperature
-4
°
F to 140
°
F (-20
°
C to +60
°
C)
Dimensions
3.5" x 4.7" x 0.9" (90 x 120 x 21.7 mm) (2
3
/
4
” deep double gang box recommended)
Floor Sensor Type
NTC (10K)
STRATA_HEAT
™
Wi-Fi Thermostat
Easy Setup Guide
