background image

Safety Information

Use Caution When Working With Batteries

2

2-12

Lastec//021819

Safety Information

2.9

Use Caution When Working With Batteries

DANGER!

 

Batteries expel explosive gases. Keep sparks, flames, burning cigarettes, or other 
ignition sources away at all times. Always wear safety goggles and a face shield 
when working near batteries. Failure to do so may cause serious injury.

1

WARNING! 

Charge the battery in a well ventilated area. Do not attempt to charge a frozen bat-
tery. 

Battery posts, terminals and related accessories contain lead and lead compounds, 
chemicals known to the State of California to cause cancer and reproductive harm. 
Wash hands after handling.

Use extreme care to avoid spilling or splashing electrolyte (which is dilute sulfuric acid) as 
it can destroy clothing and burn the skin. If electrolyte is spilled or splashed on clothing or 
the body, it should be neutralized immediately and then rinsed with clean water. A solu-
tion of baking soda, or household ammonia, and water may be used as a neutralizer.   

Electrolyte splashed into the eyes is extremely dangerous. If this should happen, force 
the eye open and flood it with cool, clean water for approximately fifteen minutes. A doc-
tor should be called immediately when the accident occurs and “on-the-spot” medical 
attention given if possible. If a doctor cannot come to the scene of the accident immedi-
ately, follow his instructions concerning actions to take. Do not add eye drops or other 
medication unless advised to do so by the doctor. Do not place a battery or electrolyte 
(acid) within the reach of children. If electrolyte (acid) is taken internally drink large quan-
tities of water or milk. Follow with milk of magnesia, beaten egg or vegetable oil. Call a 
physician immediately.

If electrolyte is spilled or splashed on any surface of the machine, it should be neutralized 
and rinsed with clean water.

CAUTION! 

Do not overcharge the battery. Overcharging may reduce the overall service life of 
the battery.

1.Battery Council International, copyright 1987

Danger

Warning

Caution

Содержание 3573C






































































Отзывы: