MANUAL FOR USE AND MAINTENANCE S5
MANUAL FOR USE AND MAINTENANCE S5
8
LSC 011 REV. 00
HEATING PHASE AND PRESET PHASE FOR OPERATION
a) Fasten the filterholders (11) to the brewing groups (16).
b) Open steam valves (5) by moving the levers upwards and leave them open, then move the steam wands
(8) over the grid (10).
c) Wait for steam coming out from the steam wands (8) (about 15/20 minutes) then close the steam valves
(5) by moving the levers back to the initial position.
d) Wait for the machine to reach the operating temperature, which is visualized on the pressure gauge of
the machine (4) (1 bar pressure), or check on the control panel (13) that the temperature, measured in
°
C and set during installation, has been reached.
e) During the heating phase, check on the control panel (13) that the symbols turn on gradually as the
temperature increases. The visualization starts when the temperature reaches 105
°
C and it continues
until the machine reaches its operating temperature (temperature symbol from blinking to fixed).
Every time the temperature goes below the set value, the symbol corresponding to the operating
temperature starts blinking (heating phase) until the temperature set is reached again.
N.B. The operating temperature is the temperature of the boiler during operation phase.
f) The equipment is ready for use.
COFFEE BREWING
a) Remove the filterholder (11a or 11b according if it is for 1 or 2 cups of coffee) from the brewing group
(16).
b) Fill it with ground coffee, making sure not to leave coffee powder on the upper edge of the filterholder,
and press it with the provided suitable coffee tamper.
c) Firmly attach the filterholder to the brewing group.
d) Place one or two cups below the filterholder (according if it is for 1 or 2 cups of coffee).
e) Press the delivery button (12) of the same group until you get the desired coffee dose in the cup. Then
manually stop the delivery using the same button.
f) For the EK model press any of the coffee delivery buttons with preset doses (25-26-27-28) (programmed
during installation), otherwise use the free-flow button (29).
N.B.: If you need to stop earlier a delivery started with one of the preset dose buttons, you only need
to press the button (29) of the same touchpad.
STEAMING FOR PREPARATION OF HOT DRINKS
a) Insert the steam wand (8) into the pitcher containing the drink to be heated up.
b) Move the lever (5) of the corresponding steam wand (8) upwards. Set the amount of steam as needed.
c) Once the heating phase is finished, stop the steam delivery by moving the lever (5) back to its initial
position, remove the steam wand from the pitcher and immediately clean it with a wet sponge in order
to remove any possible residues.
Do not move the lever for steam delivery (5) before inserting the steam wand (8) into the pitcher in
order to avoid possible burns.
☞
LSC 011 REV. 00
9
2
HOT WATER DELIVERY FOR INFUSIONS
a) Place the pitcher below the hot water nozzle (7).
b) Move the lever upwards (6) to open the valve until you get the desired water dose.
c) To stop the delivery, close the valve by moving the lever back to its initial position.
Do not move the lever (6) for hot water delivery before placing the pitcher below the hot water nozzle
(7) in order to avoid any possible burns.
ELECTRIC CUP-WARMER (optional)
In order to get an additional heating of the cups on the top, it is possible to use the additional electric cup-
warmer by pressing button (24) and by checking its operating status through the lighting up of the symbol
(23) on the control-panel (13). To switch it off press the same button.
WARNING!
Cups can be placed on the upper grid on top of the machine
(14), as long as they have their hollow part upwards (pict 2).
This is in order to avoid that, in the machines prearranged
to work with gas system, the part of the cup containing
coffee will come into contact with the machine itself.
When the appliance is used in conditions which may considerably decrease its temperature, by pressing
and keeping pressed the button
for about 5 seconds, you can increase the temperature inside the boiler
of 2
°
C; in this status, the symbol of the temperature set keeps blinking on the control-panel and at the same
time the symbol of the temperature increased of 2
°
starts blinking as well (for example if the SET is 120
°
C
this symbol is blinking and keeps blinking and also the 122
°
C starts blinking).
The new temperature set follows the general temperature trend, it is blinking when the machine is still during
the heating phase, and it is fixed when the temperature set has been reached.
In order to go back ot the initial phase press the button
(38) for about 5 seconds.
PRESET HOT WATER DELIVERY FOR INFUSIONS (optional)
a) Place the pitcher below the hot water nozzle (7).
b) Press the preset hot water delivery button (42).
c) The delivery will stop at the end of the programmed time during installation.
Do not press the hot water delivery push-button (42) before placing the pitcher below the hot water
nozzle (7) in order to prevent possible burns.
002
☞