MANUAL FOR USE AND MAINTENANCE S5
MANUAL FOR USE AND MAINTENANCE S5
6
LSC 011 REV. 00
1.5
INSTALLATION REQUIREMENTS MADE BY THE USER
The machine has to be placed on a stable surface
which grants a safe position. Check this important
requirement, since the manufacturer cannot be
considered liable for any damage caused by the
instability of the equipment.
While prearranging the system, consider a hole on the
bearing surface in order to carry out all electric and
water connections through the opening below where,
if recommended by the installer, the water softener
has to be placed. A hole of 10x10cm is enough in the
area (A) indicated in picture 1.
The minimum dimensions are:
- height
cm. 60
- length
cm. 40
- depth
cm. 40
Between the water supply mains and the water inlet pipe of the equipment, there must be a tap in order to
stop the flowing of water in case of need (pict. 1).
The water mains pressure must be within the range 1 and 5 bar.
If this last requirement lacks, please, consult the manufacturer.
The equipment is supplied without a plug. It is supposed to be directly connected to the electric supply mains
and so it is necessary to prearrange a single-pole switch with opening of contacts equal or superior to 3mm,
according to regulations in force (pict. 1).
The drain pipe of the equipment must be directly connected to the suitable open drain siphon, prearranged
by the customer (pict. 1).
Avoid fitting the drain pipe into basins or buckets placed under the counter, as this fact increases the forming
of dirtiness deposits and, consequently, the proliferation of bacterial flora.
WARNING! With appliances working with gas, the gas supply tap must be placed in an easily
accessible place (pict. 1), so as to prevent gas leak, in case of need.
Check periodically the deadline date of the gas pipe connecting the system to the appliance and have
it replaced by the Service Centre before the due date
WARNING! The machine is supplied without any water inside the boiler to prevent serious damage
if exposed to low temperatures.
The machine must be supplied with cold, drinkable water.
1
2
3
x
Single-pole switch with at least 3mm opening between contacts.
Water supply tap
Drain siphon
Gas supply tap (if present
)
•
•
1
y
•
•
z*
*) Distance between the back panel of the appliance and
the wall.
min. 20 cm.
min. 40 cm.
min. 10 cm.
4
Y
X
4
1
a
2
3
X
001
LSC 011 REV. 00
11
EVERY 15 DAYS
After tuning off the machine, remove the shower heads with the provided tool, brush them carefully, making
sure that all the holes are clean. Then reassemble them following the sequence shown in pict. 3.
WARNING!
Every day, after daily work and cleaning, switch off the machine using the main switch of the system,
the water supply tap and eventually also the gas supply tap, if present (pict 1 page 6).
Do not use water jets to clean the machine.
WATER SOFTNER
If the installation of the water-softner has been recommended because of hard water and limescale in the
water mains, it is necessary to follow the instructions of the water softener’s manufacturer (periodic
regeneration).
1b) To regenerate the water in the boiler on appliances with preset hot water dose (optional).
•
Place a high temperature resistant container below the hot water nozzle (7) to prevent hot water spills.
•
Press and keep pressed the hot water delivery push-button (42) for at least 5 seconds; the automatic
boiler emptying out cycle starts (in this phase all the controls of the machine are not enabled).
•
At the end of the cycle, the appliance recovers the correct water level inside the boiler through the
automatic refill system.If you want to interrupt the cycle it is enough to press the water delivery push-
button (42).
•
Disconnect the appliance.
2) Proceed then with the cleaning of the filterholders and the filters with the provided brush, making sure
no dirtiness is left inside the filterholders and that all the filter holes are clean.
3) Clean the shower heads below the brewing groups with the brush.
4) Clean the water drip-tray (9) and the drip-tray grid (10), by using, if necessary, regular detergents.
a
b
c
d
e
tightening screw
small shower head
big shower head
shower-heads block
brewing group
3
d
c
a
b
e
003