1. Inclinarla
Cabeza del Ventilador hacia atrás. Coloque la Rejilla
Trasera en el Motor. (Figura 7)
2. Alinear la lengüeta de la
Rejilla Trasera con la ranura en la parte
superior de la cubierta delantera del
Motor.
PASO 4: ENSAMBLE DEL ASPAY REJILLA
PASO 2: ENSAMBLE DEL PIE
COLOQUE LA BASE EN EL PISO
1. Utilizando un movimiento giratorio, inserte el extremo del tubo de
diámetro grande en el agujero de la
Base. (Figura 5) El girar el tubo
a medida que se lo empuja asegura que el tubo quede plenamente
asentado en la
Base.
2. Para ajustar la altura:
a) Afloje la
Tuerca de Ajuste de Altura.
b) Eleve o baje el
Tubo de Extensión hasta obtener la altura
deseada.
c) Apriete la
Tuerca de Ajuste de Altura.
1. Coloque el
Conjunto de Cabezal
con el
Collar en el Tubo de
Extensión. (Figura 6)
2. Sostenga firmemente el
Tubo de
Extensión y empuje el Conjunto
de Cabezal hacia abajo con un
movimiento giratorio hasta que
quede asentado en el
Tubo de
Extensión.
PASO 3: CONJUNTO DE LA CABEZA
1. Saque el conjunto de la tubería del cartón como muestra.
(Figura 1)
2. Desafloje la
Tuerca de Ajuste de Altura, girando en sentido
contrahorario.
(Figura 2)
3. Eleve la
Extensión De La Tubería. (Figura 3)
4. Apriete la
Tuerca de Ajuste de Altura, girando en sentido
horario.
(Figura 4)
PASO 1: ARMADO DE LA TUBERÍA
3. Asiente la
Parrilla Trasera y sujetela con la Tuerca de Plástico
hacia la Derecha. Deslice la
Helice en el Eje del Motor. (Figura
8) Alinear la Ranura Del Cubo de la tapa con el Pasador del eje
del motor.
(Figura 8A)
4. Para asegurar la
Helice, enroscarla
hasta que quede apretada en el
Cubo
de la Tapa haciéndola girar Hacia la
Izuierda.
2085381
Rev. D 2/05 (BREEZE)
6
2085381
Rev. D 2/05 (BREEZE)
3
Conjunto de
Cabezal
Figura 2
Figura 4
Figura 3
Figura 1
Tuerca de
Ajuste de
Altura
Tubería de
Extension
Figura 5
Tubo de Extensión
Tuerca de Ajuste
de Altura
Base
Collar
Tubo de
Extensión
Figura 6
Rejilla
Trasera
Figura 7
Motor
Figura 8
Parrilla Trasera
Helice
Tuerca de
Plastico
Tapa de
Ventilador
Figura 8A
Pasador
Ranura del
Cubo
This Fan may be operated by the Manual Controls located on top
of the unit (as shown in
Figure 11) or by the Remote Control
(shown in
Figure 12).
1. Remove the Fan from the carton and assemble as instructed.
2. Place the Fan on a firm, level surface.
WARNING:
Plastic or rubber tabs, like the feet on this unit, may
stick to hardwood floors. The unit may leave a residue that could
darken, stain or leave permanent blemishes on the finish of certain
hardwood floors.
3. Plug the power supply cord into a 120 V~ electrical outlet. Be
sure plug fits tightly in outlet.
4. Install two AAA batteries supplied as shown in
Figure 12.
5. Apply power to your fan by pushing the
Power/Speed Button (
)
manually on the fan, or the
Power Button ( ) on the remote control.
6. FAN SPEED: You may now adjust the fan speed to the desired
level, 1 (Low), 2 (Medium), or 3 (High) by pressing the
Power/
Speed Button (
)Power/Speed button on the fan or by pressing
the
Speed Button (
) on the remote .
7. TIMING FUNCTION: This fan is equipped with a timer that
allows you to set the length of operation by pressing the
Timing Function Button (
) manually on the control area
of the fan, or by pressing the
Timing Button (
) on the
remote control. Press the key once for one hour, twice for
two hours, a third time for four hours. A fourth time will
reset the fan to continuous running mode.
8. BREEZE MODE: The Breeze Mode allows the fan to ran-
domly cycle through the speeds. With the fan on, press the
Breeze Mode Button (
) on the control area of the fan, or
the
Breeze Button (
) on the remote control. If the fan speed
setting is on Low speed (1), it will cycle from off to low. Me-
dium speed (2) will cycle from off, low and medium. High
speed (3) will cycle from off, low, medium and high. The speed
indicator light will flash in Breeze Mode. Press the
Breeze
Mode Button (
) again to turn off the Breeze Mode.
9. OSCILLATION: Push down oscillation knob on motor housing
to make fan head move from side to side.
(Figures 13 and 14)
10. Your Remote Pedestal Fan has also been provided with
Attach-
ment Strips. Remove the Film from rear of Attachment Strip
and adhere to remote. Remove Film from rear of the other At-
tachment Strip and adhere to your fan. Now you can store your
remote control when not in use.
(Figure 15)
OPERATION
+
+
TM
Figure 11
Timer Length
6. With fan head in upright position, align
Ornament of Front Grill
so it is horizontal and right side up. By starting with the top of
the grill and working down, insert
Snaps on Rear Grill through
Slots in Front Grill. (Figure 10)
Ornament
Slots
Snaps
Rear Grill
Front Grill
Figure 10
2. Instale el Ornamento en la Parrilla Delantera. Despegue el
autoadhesivo del Ornamento. Inserte la Lengüeta en la Ranura
Rectangular. Presione el Ornamento hasta que quede fijo.
(Figura
8)
Ranura
OPERATION
Down: Oscillate
Up: Stationary
Figure 13
Figure 14
Power / Speed
Button
Timing Function
Button
Breeze Mode
Button
Figure 12
Breeze Mode
Button
Power
Button
Speed Button
Timer
Function
Button
AAA
Batteries
Attachment
Strips
Figure 15
Adhesive
Film
Ornamento
Lengüeta
Figura 9