Manual: RS 800 G US, RS 800 RGY US, RS 1000 RGB US, RS 2300 RGB US RS-2700 RGB US
5 / 9
Revision Jun-13
Rotation
192~255
Rotate h. & v.
7
Dot rotation
0~63
No function
64~127
Rotating
192~255
Rotating & Dotting
8
Move
0~63
No function
64~127
Move horizontally
128~191
Move vertically
192~255
Move h. & v.
9
Extend
0~63
No function
64~127
Extend horizontally
128~191
Extend vertically
192~255
Extend h. & v.
10
Zoom
0~85
No function
86~169
Small to large
170~255
Large to small
11
Drawing speed
0~255
slow to fast
12
Scan speed
0~255
slow to fast
13
Colour speed
0~255
slow to fast
14
Size
0
Original size
1~255
Small to large (120 = original)
Maintenace / cleaning
Always disconnect from mains before cleaning/opening the laser. You can open the device by
removing the top: remove the mounting bracket (4 quick locks), the 5 Philips screws, and the eye
bolt.
Regularly clean the interior from dust, especially ensure operation of the fans. To clean the mirrors,
ideally use acetone and lens cleaning paper (fold paper to get an edge with which to clean the
mirrors). If not available, you can also use window cleaner, and a paper towel. Be careful, even light
scratches reduce the output power of the laser; always clean with strokes in one direction, to
minimize the effect of scratches. Mirrors need cleaning, when a “halo” is noticeable around the beam,
or an unusual high amount of diffuse light can be seen inside the device. When fog fluid condenses in
the device, clean all traces, and rearrange the position of fazer and/or laser.
Technical specifications
Output power (at the laser):
RS 800 G: min. 550mW, max. 800mW, >550mW, 532nm green
RS 800 RGY: min. 600mW, max 800mW, >250mW 532nm green, >350mW 655nm red
RS 1000 RGB: min. 750mW, max 1000mW, >200mW 532nm green, > 300mW 655nm
red, >250mW 445nm blue
RS 2300 RGB: min. 1550mW, max 2300mW, >250mW 532nm green, > 300mW 640nm
red, >1000mW 445nm blue
RS 2700 RGB: min. 1800mW, max 2700mW, >500mW 532nm green, > 300mW 640nm
red, >1000mW 445nm blue
Lasersources:
air-cooled DPSS laser (green), laser diode (blue with RGB, red with RGB and
RGY models)
Laser class:
4
Modes:
ILDA, DMX 512, auto, music active
ILDA:
25pin ILDA standard Sub-D shaped 25pin connector
Galvos:
50k scanspeed
DMX 512:
14 channels
Patterns:
160
Scanangle:
set to ca. 40° optical (60° max)
Beam:
ca. 3mm/1mrad, blue with RS-2300 RGB 4x1mm, 3mrad
Accessories:
power cable, key switch, interlock plug, manual, safety cord
The laser comes in a flightcase.
Input voltage:
AC 110~120V or 220~240V switchable 50/60Hz
Power consumption:
120W
dimensions:
21.6”x12.6”x12.2” (55 x 32 x 31cm) (W x D x H)
Weight:
33lbs (15kg) Laser,
total:
62lbs (28kg)
(with flight case)
Operating temperature:
50~95°F (
10°-35°C)
Loudness:
<70dB
