3
Instruction Manual
Cable and Bar Cutter “CC0018”
MODELS
CC0118
CC0140
CC0175
CC0190
CC01120
CC0160
CAPACITY
kN
54 kN
135 kN
70 kN
109 kN
109 kN
437 kN
PRESSURE
bar
550 bar
700 bar
700 bar
700 bar
700 bar
700 bar
WIRE ROPE
STEEL
Ext. mm
ALUMMINIUM
Ext. mm
18 mm
18 mm
40 mm
40 mm
40 mm
-
35 mm
-
35 mm
-
60 mm
60 mm
CABLE
TELÉPHONE
Ext. mm
LEAD
Ext. mm
UNDERGROUND
Ext. mm
-
18 mm
18 mm
-
40 mm
40 mm
75 mm
75 mm
75 mm
90 mm
90 mm
90 mm
120 mm
120 mm
120 mm
-
-
-
STEEL ROPE
MAX.R = 1800 N/mm
Ext. mm
WIRE
min. mm
18 mm
1 mm
32 mm
2 mm
-
-
-
-
-
-
60 mm
3 mm
BAR MAX.R= 400
N/mm
STEEL
Ext. mm
COPPER
Ext. mm
ALUMMINIUM
Ext. mm
12 mm
15 mm
15 mm
20 mm
30 mm
30 mm
-
-
-
-
-
-
-
-
-
25 mm
35 mm
35 mm
BLADE
CRC 18
CRC-35-40
CRC75
CRC0190
CRC01120
CRC0160
DIMENSIONS
A mm
B mm
C mm
212 mm
60 mm
19 mm
290 mm
92 mm
41,5 mm
451 mm
126 mm
75 mm
535 mm
146 mm
92mm
635 mm
178 mm
122 mm
388 mm
105 mm
64 mm
WEIGHT
kg
2 kg
4,5 kg
5,5 kg
10 kg
11,7 kg
15,6 kg
3. ESSENTIAL SAFETY REQUIREMENTS.
In the event of the improper working of the machine or one of the connected elements, immediately halt all operation, depressurise the system and solve the
problem.
Before beginning operation, make sure that the dangerous area is free of people.
Always use the tools in well-lit areas.
Regardless of whether the cutting tool has a built-in or separate pump, try to establish the most convenient and stable working method for both the tool and the
operator.
When cutting the work piece may project particles and fragments. Therefore, the operator should protect his/her body and (particularly) eyes using appropriate
protective equipment.
Goggles
Face Protection.
In the case of tools with a separate pump, the hose enables the operator to move further away from the dangerous area, while in the case of tools with built-in
pumps, if possible, a guard should be positioned between the work piece and the operator.
Do not expose tools to intense heat sources, such as welding equipment, for example.
Depressurise and disconnect the tools before carrying out any maintenance operations.
The controls of both the tools with built-in pumps and the separate pumps themselves should always be activated manually. Do not use hand tools, levers, etc.
to work the controls.
In the case of tools with separate pumps, make sure all the quick plugs are completely clean before connecting.
Make sure that the hydraulic hoses are neither twisted nor unduly tensed.
When working with an electric pump, make sure that the valve is set to its neutral position before connecting the tool.
When working with cable cutters, fraying may occur during the cutting operation. To avoid this, clamp the cable to either end of the cutting blade with tape,
wire or even a bushing.
Clean the quick plugs thoroughly before connecting.
In all cases, the operator should be thoroughly trained in the operation of the tool and should act in accordance with the logical safety criteria associated with
the use of high-pressure equipment.
Allow for a general use at 80% of the tool’s nominal capacity. Do not exceed the tool’s nominal capacity.
In the case of tools with separate pumps, we recommend the use of a pressure indicator, to enable the operator to monitor at all times
the force which the system is subjected.
Check that the machine and accessories have not been damaged in any way during transportation to the plant.
