![background image](http://html.mh-extra.com/html/larson-electronics/golight-stryker-gl-3049-p/golight-stryker-gl-3049-p_instruction-manual_676957002.webp)
The GL-3049-P Light is a 2-Speed Searchlight with
Directional Flexibility which gives the operator a full
370° horizontal rotation and a 135° vertical tilt with
fingertip control. The Stryker Light provides superior
light penetration with the new Cr5 PentaBeam II
technology.
GL-3049-P Light Wireless - Permanent Mount:
Searchlight
Remote Control (Per Model Number) 2 - 23A 12V
Batteries Permanent Mounting Gasket Permanent
Mounting Plate Mounting Screws
Rockguard
GL-3049-P Light Wireless - Magnetic Mount:
Searchlight
Wireless Hand Held Remote Control
2 - 23A 12V Batteries
Rockguard
MOUNTING INSTRUCTIONS
Light Unit/Magnetic Mount
Select the best location for the magnetic mount
Stryker. Make sure the metal area under the
magnetic base is flat and clean to ensure a strong
bond. Route the power cord and connect to power
outlet. The magnetic mount should be removed from
vehicle exterior when traveling at excessive speeds
and in strong wind conditions.
The ball and socket style mounting base provides
flexible adjustment while mounted. The Golight is
permanently mounted via four holes in the base plate
or magnetically mounted with a 200 pound grip
magnetic base depending on model purchase.
To adjust ball socket, loosen
the hand screw on the side of
mount and move arm around
until it is in the desired
location. Tighten hand screw
to lock mount in place.
When removing from painted surfaces, pull
magnet straight up and away from the surface to
prevent scratches. Do not drag.
Wireless Dash Control
If you have a wireless dash control, please note that
it is vital for this to be attached to a flat / smooth
surface with the 4 mounting screws included. The
arrow under the rubber cover should point up.
BATTERY INSTALLATION AND REMOVAL FOR
TRANSMITTER
Remove battery cover: for wireless hand-held
transmitter, remove phillips head screw to remove
cover. For wireless dash mount remote, simply
remove the exterior rubber cover. With battery
compartment now exposed, insert batteries
according to the correct polarity or gently remove
batteries by grabbing the positive end and lifting up.
PROGRAMMABLE REMOTE INSTRUCTIONS
The GL-3049-P Light is controlled with a
programmable remote with 2187 different channels.
This feature allows you the freedom to change the
channel selection, and the receiver re- learns the
new selection. This light has been pre-programmed
at the factory, and it is not necessary to re-program
the transmitter, unless you experience outside
interference. To program transmitter:
1. IMPORTANT:
Disconnect power.
2.
Remove battery cover from remote control.
3.
Set the 7 dip switches to a selection of your
choice. There are 3 positions on each; positive,
negative and neutral. Use a small screwdriver
and select a position for each dip switch. *Please
note that the orientation of the +/- switch
positions may vary among different models of
wireless remote controls.
4.
Insert both GP 23A 12V batteries. Be sure
batteries have adequate charge.
5.
Replace battery cover.
a.
Depress the on/off button and hold it
down. Red LED will light.
b.
While holding the on/off button down,
reinstall the power (replace fuse or
connect vehicle battery).
c.
Keep on/off button depressed for 5-6
seconds, and then release. The light
should now be programmed.
OPERATION OF GL-3049-P
1.
Using the remote control, turn on the light by
moving the on/off switch.
2.
With the joystick on the dash control, rotate your
light to the desired location.
3.
The speed of the light rotation can be controlled
by depressing the fast/slow button one time and
by depressing it again to restore the original
speed.
4.
The spotlight should not be turned on when the
snap on lens cover (rockguard) is attached. The