Lars Thrane Iridium Certus 200 Скачать руководство пользователя страница 56

Страница: 56 / 141

LT-4200 User & Installation Manual Rev. 1.00

Change of Hardware and Software

Lars Thrane A/S

www.thrane.eu

Page 45 of 128

Change of Hardware and Software

This section will provide some guidance and instructions on replacing system units or updating software.

Change of Hardware

This section will provide some guidance on replacing system units and what the user of the LT-4200 system
should be aware of, see Table 16.

Always remove the DC input power to the LT-4200 system when changing the hardware and system units.

NOTE

Changing the Certus SIM card may require involving of an Iridium Certus Service Provider
(SP). For details of the Iridium Certus Service Provider (SP), see

Activating the System

page 43.

Change of Hardware

Hardware

Procedure

Comments

LT-4210 Control Unit

The LT-4210 CU can be replaced by swapping
the hardware. Remember the Certus SIM card

from the ‘old’ LT

-4210 CU.

All user data (contacts and call
history) will be lost since the
LT-4210

CU is the ‘master’ of

the system.

LT-3120 Handset

Change hardware.

Test the new hardware.

LT-3121 Cradle
LT-4230 Antenna Unit
Certus SIM Card

The Certus SIM card can be replaced with a
new Certus SIM card.

Only a Certus SIM card can be
used in the LT-4200 system.
Check status of the Certus SIM
card with an Iridium Certus
Service Provider.

Table 16: Change of Hardware in the LT-4200 system

Содержание Iridium Certus 200














































































































































Результаты поиска

Содержание Iridium Certus 200

Отзывы:

Похожие инструкции для Iridium Certus 200

Бренды по названию

Популярные бренды

Lars Thrane Iridium Certus 200, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание Iridium Certus 200

Отзывы:

Похожие инструкции для Iridium Certus 200

Бренды по названию

Популярные бренды