Larkin M5500 Скачать руководство пользователя страница 13

Страница: 13 / 14

Diode Modules for Rotating Rectifiers

Make sure the Voltage Control is at the zero position (fully counter

clockwise) before turning the unit on. Connect the Anode and Cathode

leads to the diode to be tested.

NOTE

: Diodes only have to be tested in one direction. If the diode is

forward biased (standard), the function switch should be in the PRV

position. If the diode is reversed biased, the function switch should be in

the PFV position.

Place the function switch in the PRV (PFV) position and press the

“

TEST

”

button.

Slowly increase the voltage while observing the Peak Voltage and Peak

Leakage Current on the panel meters.

In a properly functioning device, the rated voltage should be reached before

the current starts to rise

rapidly

, (the

“

break

over point

”).

Both diodes in this modules are rated at 2600 V.

Содержание M5500















Результаты поиска

Содержание M5500

Отзывы:

Похожие инструкции для M5500

Бренды по названию

Популярные бренды

Larkin M5500, Руководство пользователя

Результаты поиска

Содержание M5500

Отзывы:

Похожие инструкции для M5500

Бренды по названию

Популярные бренды