Lapple FIBRO FIBROTOR EM.NC Series Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 60

Lapple FIBRO FIBROTOR EM.NC Series Скачать руководство пользователя страница 40

9 REPAIR

9.2 MAINTENANCE WORK

FIBROTOR

40

|

60

9.2

Maintenance work

The following activities are considered maintenance work:

•

Inspection

•

Maintenance / cleaning

•

Repair

9.2.1

Inspections

Daily before the start of the work shift:

•

Inspection of the essential functional units.

•

Inspection of the air pressure on the manometer.

•

Inspection of the filter bowl for the accumulated condensate.

9.2.2

Maintenance / cleaning

Turn off the machine in a secure manner

Performing  maintenance  and cleaning  work when  the  power supply  is turned  on  is
dangerous.  Perform the  5 steps to securely  turn  off the  electric power supply.  All
other power supply sources must be also turned off. Injuries when the power supply
is turned  on.

5 steps for securely turning off the electric power supply.

•

Turn off the main switch (disconnect all sides)

•

Secure the main switch against re-starting

•

Check for absence of voltage

•

Ensure the grounding of all sides

•

Cover any live neighbouring parts

After the work has been completed, the shut-down must be in cancelled in the
reverse order.

«
...
38
39
40
41
42
...
»

Содержание FIBRO FIBROTOR EM.NC Series





























































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды