manualshive.com logo in svg

Lantronix WiPort-485, Руководство пользователя, Страница: 45 / 75

Поделиться
Скачать
Lantronix WiPort-485 Скачать руководство пользователя страница 45

Configuration via Serial Mode or Telnet Port 

WiPort™ User Guide 

 

45 

 

Manual Connection 

Attempts to connect when directed by a command string 
received from the serial port. The first character of the command 
string must be a 

C

 (ASCII 0x43), and the last character must be 

either a carriage return (ASCII 0x0D) or a line feed (0x0A). No 
blanks or space characters may be in the command string. 
Between the first and last command string characters must be a 
full or partial destination IP address and can include a 
destination port number.  
 
The IP address must be in standard dot-decimal notation and 
may be a partial address, representing the least significant 1, 2, 
or 3 bytes of the remote IP address. The period is required 
between each pair of IP address numbers. 
 
If present, the port number must follow the IP address, must be 
presented as a decimal number in the range 1-65535, and must 
be preceded by a forward slash (ASCII 0x2F). The slash 
separates the IP address and the port number. If you omit the 
port number from a command string, the internally stored remote 
port number starts a connection.  
 
If a partial IP address is presented in a command string, it is 
interpreted to be the least significant bytes of the IP address and 
uses the internally stored remote IP address to provide the most 
significant bytes of the IP address. If the IP address entered is 
0.0.0.0/0, the device server enters Monitor Mode. 
 
For example, if the remote IP address already configured in the 
unit is 129.1.2.3, then an example command string would be 
C3/7. (This would connect to 129.1.2.3 and port 7.) You may 
also use a different ending for the connection string. For 
example, C50.1/23 would connect you to 129.1.50.1 and port 23. 

Table 5-7. Manual Connection Address Example

 

Command String  

Result if remote IP is 129.1.2.3 and remote port is 1234  

C121.2.4.5/1  

Complete override; connection is started with host 121.2.4.5, port 1  

C5  

Connects to 129.1.2.5, port 1234  

C28.10/12  

Connects to 129.1.28.10, port 12  

C0.0.0.0/0 

Connects to 129.1.28.10, port 12; enters Monitor Mode 

 

Autostart (Automatic 
Connection) 

The unit automatically attempts a connection to the remote IP 
address and port after booting up.  

Содержание WiPort-485












































































Отзывы:

Нет отзывов