manualshive.com logo in svg

Lantronix WiPort-485, Руководство пользователя, Страница: 26 / 75

Поделиться
Скачать
Lantronix WiPort-485 Скачать руководство пользователя страница 26

Configuration using Web-Manager 

26  

WiPort™ 

User 

Guide 

Figure 4-5. Channel Serial Settings 

 

2.  In the available fields, enter the following information: 

Channel 1 

Disable Serial Port 

Available on Channel 1 settings only.  When selected, 
disables communication through the serial port. 

Port Settings 

Protocol 

Select the protocol type from the pull down menu for the 
selected channel.  

RS-422/485 4-wire

 and 

RS-485 2-wire

 

options are available on the WiPort-485 only. 

Flow Control 

Flow control manages data flow between devices in a network 
to ensure it is processed efficiently.  Too much data arriving 
before a device is prepared to manage it causes lost or 
retransmitted data. 

Baud Rate 

The unit and attached serial device, such as a modem, must 
agree on a speed or baud rate to use for the serial connection. 
Valid baud rates are 300, 600, 1200, 2400, 4800, 9600 
(default), 19200, 38400, 57600, 115200, 230400, 460800, or 
921600. 

Data Bits 

Indicates the number of bits in a transmitted data package. 

Parity 

Checks for the parity bit.  The default is 

None

. 

Stop Bits 

The stop bit follows the data and parity bits in serial 
communication.  It indicates the end of transmission. 

Содержание WiPort-485












































































Отзывы:

Нет отзывов