Lantronix SM4T4DPA Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 29

Lantronix SM4T4DPA Скачать руководство пользователя страница 12

Lantronix

SM4T4DPA Install Guide

33867 Rev. A

https://www.lantronix.com

Page

12

of

29

Installation

Selecting a Site

The Switch can be mounted in a standard 19-inch equipment rack (Via Optional Rack mount Kit) or on a flat
surface. Be sure to follow the guidelines below when choosing a location.

◆

The site should:



Be at the center of all the devices you want to link and near a power outlet.



Be able to maintain its temperature within 0 to 40°C (32 to 104 °F) and its humidity within 10% to 90%, non-

condensing.



Be accessible for installing, cabling and maintaining the devices.



Allow the status LEDs to be clearly visible.

◆

Make sure the twisted-pair Ethernet cable is always routed away from power lines, radios, transmitters or any

other electrical interference.

◆

Make sure that SM4T4DPA Switch is connected to a separate grounded power outlet that provides 100 to 240

VAC, 50 to 60 Hz.

Ethernet Cabling

To ensure proper operation when installing the switch into a network, make sure that the current cables are suitable
for 100BASE-TX or 1000BASE-T operation. Check the following criteria against the current installation of your
network:

◆

Cable type: Unshielded twisted pair (UTP) or shielded twisted pair (STP) cable with RJ-45 connectors; Category

5 or Category 5e with maximum length of 100 meters is recommend 100BASE-TX, and Category 5e or 6 with
maximum length of 100 meters is recommend for 1000BASE-T.

◆

Protection from radio frequency interference emissions.

◆

Electrical surge suppression.

◆

Separation of electrical wires and data based network wiring.

◆

Safe connections with no damaged cables, connectors or shields.

RJ-45 Connections

SFP Transceiver

«
...
10
11
12
13
14
...
»

Содержание SM4T4DPA






























Отзывы:

Нет отзывов