Lantronix MSS Скачать руководство пользователя | Manualshive

Страница: 2 / 93

background image

The information in this guide may change without notice. The manufacturer assumes no responsibility for any errors
which may appear in this guide.

UNIX is a registered trademark of The Open Group. Ethernet is a trademark of XEROX Corporation. DEC and LAT
are trademarks of Digital Equipment Corporation. Centronics is a registered trademark of Centronics Data Computer
Corp. PostScript is a trademark of Adobe Systems, Inc. NetWare is a trademark of Novell Corp. AppleTalk, Chooser,
and Macintosh are trademarks of Apple Computer Corp. LaserJet and Bitronics are trademarks of Hewlett Packard.
Windows is a trademark of Microsoft.

UNIX is a registered trademark of The Open Group. Ethernet is a trademark of XEROX Corporation. DEC and LAT
are trademarks of Digital Equipment Corporation. Centronics is a registered trademark of Centronics Data Computer
Corp. PostScript is a trademark of Adobe Systems, Inc. NetWare is a trademark of Novell Corp. AppleTalk, Chooser,
and Macintosh are trademarks of Apple Computer Corp. LaserJet and Bitronics are trademarks of Hewlett Packard.
Windows is a trademark of Microsoft.

UNIX is a registered trademark of The Open Group. Ethernet is a trademark of XEROX Corporation. NetWare is a
trademark of Novell Corp. Windows is a trademark of Microsoft.

DEC, thickwire, thinwire, VMS, VT100, and ULTRIX are trademarks of Digital Equipment Corporation. UNIX is a
registered trademark of AT&T. Ethernet is a trademark of XEROX. NetWare is a trademark of Novell Corp. Apple-
Talk, Chooser, and Macintosh are trademarks of Apple Computer Corp. Windows NT and Windows for Workgroups
are trademarks of Microsoft Corporation. Security Dynamics and SecurID are registered trademarks and PASSCODE,
PINPAD and ACE/Server are trademarks of Security Dynamics Technologies Inc..

Copyright 2000, Lantronix. All rights reserved. No part of the contents of this book may be transmitted or reproduced
in any form or by any means without the written permission of Lantronix. Printed in the United States of America.

The revision date for this manual is

30 January, 2001

.

Part Number: 900-157

Rev. B

WARNING

This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of
FCC Rules. These limits are designed to provide reasonable protection against such interference when operating in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed
and used in accordance with this guide, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause interference in which case the user, at his or her own
expense, will be required to take whatever measures may be required to correct the interference.

Changes or modifications to this device not explicitly approved by Lantronix will void the user's authority to operate
this device.

Cet appareil doit se soumettre avec la section 15 des statuts et règlements de FCC. Le fonctionnement est subjecté aux
conditions suivantes:

(1) Cet appareil ne doit pas causer une interférence malfaisante.

(2) Cet appareil doît accepter n'importé quelle interférence reìue qui peut causer uneopération indésirable.

«
1
2
3
4
...
»

Содержание MSS






























































































Отзывы:

Нет отзывов

Похожие инструкции для MSS

Бренд: Xerox Страницы: 12

SUPERSERVER 6021F

Бренд: Supermicro Страницы: 116

SBXL52 - Server Compute Blade

Бренд: Intel Страницы: 126

ProLiant DL580 Gen10

Бренд: HPE Страницы: 158

SUPERSERVER 6015C-M3

Бренд: Supero Страницы: 118

88743BU - System x3950 E

Бренд: IBM Страницы: 426

Бренд: IBM Страницы: 98

Бренд: AC&T System Страницы: 32

Бренд: Hamlet Страницы: 76

Бренд: Black Box Страницы: 30

Бренд: Olive Страницы: 103

Alcatel-Lucent OXO Connect Compact

Бренд: Nokia Страницы: 216

SILVERSTREAM 3.75

Бренд: RSA Security Страницы: 11

Бренд: Planet Страницы: 83

Бренд: Medialon Страницы: 88

Бренд: Blonder tongue Страницы: 20

@server iSeries

Бренд: IBM Страницы: 294

Бренд: C-MOR Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды