Lantronix FOX3-2G Series Скачать руководство пользователя страница 44

Страница: 44 / 51

Hardware Interfaces

FOX3-2G/3G/4G Series Hardware Manual

7.6.

Mounting

FOX3-2G/3G/4G offer different mounting possibilities, depending on the kind of the antenna used.

When installing one of FOX3-2G/3G/4G with internal antennas, please make

sure the FOX3-2G/3G/4G' back side with the text "THIS SIDE TO SKY" is facing

up to the sky, with no metal objects above or under the device case that can

interfere with GPS reception.

When installing a FOX3-2G/3G/4G with external antennas, there are two

connectors on the device for connecting a GPS/GNSS antenna such as FAL-

ANT-11

(shown in figure below) or

FAL-ANT-12. During the installation,

please make sure the receiving side of the GSM/GPS antenna is up, with no

metal object above or under the antenna and device that interfere with GPS

reception.

Each of FOX3-2G/3G/4G provide 8 holes to be attached to suitable locations (see figure below). It

can be mounted in different directions and different locations such as on wall or in vehicle.

Fasteners can be Hexagon head with collar self drilling screws DIN 7504 K, ST3.5 x 32(12) mm and

different length.

There are no screws included in the delivery pack.

More detailed information how

to install the device in the vehicle, refer to the application note

"AppNotes_AVL_Installation_Guide.pdf".
FOX3-2G/3G/4G are NOT waterproof or sealed devices. Care must be taken to ensure the devices

are kept away from water or any other liquids.

Figure 25:

View of the mounting holes

7.6.1.

External Antenna Ports

FOX3-2G/3G/4G are fitted with two male

SMB FAKRA

connectors that accept a wide variety of

GSM/GNSS antenna styles for using external antennas instead of the internal ones. The

Bordeaux

connector

(see figure below)

is for connecting a GSM antenna. The

Blue

connector

(see figure

below)

is for connecting a GNSS antenna.

There is no antenna included in the standard delivery, it

needs to be ordered separately.

We provide two combined

GSM/GNSS

antenna (FAL-ANT11) especially, for the FOX3 series, the

2G/3G/GNSS antenna (FAL-ANT-12) for FOX3-3G series and FAL-ANT-14 for FOX3-4G Series.
For more details about the FAL-ANT-11, FAL-ANT-12 and FAL-ANT-14, refer to the data sheet

available on our web page.

Содержание FOX3-2G Series




















































Результаты поиска

Содержание FOX3-2G Series

Отзывы:

Похожие инструкции для FOX3-2G Series

Бренды по названию

Популярные бренды

Lantronix FOX3-2G Series, Руководство по оборудованию

Результаты поиска

Содержание FOX3-2G Series

Отзывы:

Похожие инструкции для FOX3-2G Series

Бренды по названию

Популярные бренды