background image

 

9

 

Powerful 

water jets 

Water projected in powerful 

jets (12.5 mm nozzle) 

against the enclosure from 

any direction shall have no 

harmful effects. 

Test duration: at least 

3 minutes 

Water volume: 100 litres per 

minute 

Pressure: 100 kPa at 

distance of 3 m 

Immersion 

up to 1 m 

Ingress of water in harmful 

quantity shall not be 

possible when the 

enclosure is immersed in 

water under defined 

conditions of pressure and 

time (up to 1 m of 

submersion). 

Test duration: 30 minutes 

Immersion at depth of at 

least 1 m measured at 

bottom of device, and at least 

15 cm measured at top of 

device 

Immersion 

beyond 1 m 

The equipment is suitable 

for continuous immersion in 

water under conditions 

which shall be specified by 

the manufacturer. 

Normally, this will mean 

that the equipment is 

hermetically sealed. 

However, with certain types 

of equipment, it can mean 

that water can enter but 

only in such a manner that 

it produces no harmful 

effects. 

Test duration: continuous 

immersion in water 

Depth specified by 

manufacturer 

Powerful 

high 

temperature 

water jets 

Protected against close-

range high pressure, high 

temperature spray downs. 

— 

 

Содержание TPGS-L6216XT

























Отзывы: