background image

 

 

FCC Warning 

 

This  Equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a 

Class-A  digital  device,  pursuant  to  Part  15  of  the  FCC  rules.  These  limits 

are designed to provide reasonable protection against harmful interference 

in  a  residential  installation.  This  equipment  generates,  uses,  and  can 

radiate radio frequency energy. It may cause harmful interference to radio 

communications  if  the  equipment  is  not  installed  and  used  in  accordance 

with  the  instructions.  However,  there  is  no  guarantee  that  interference  will 

not  occur  in  a  particular  installation.  If  this  equipment  does  cause  harmful 

interference  to  radio  or  television  reception,  which  can  be  determined  by 

turning  the  equipment  off  and  on,  the  user  is  encouraged  to  try  to  correct 

the interference by one or more of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that to 

which the receiver is connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

 

 

CE Mark Warning 

 

This  is  a  Class-A  product.  In  a  domestic  environment  this  product  may 

cause  radio  interference  in  which  case  the  user  may  be  required  to  take 

adequate measures. 

 

 

 

 

 

 

Содержание IPES-0005B Series


















Отзывы: