Lanier R/C S.E.5A Скачать руководство пользователя страница 3

Страница: 3 / 16

ITEMS NEEDED TO COMPLETE THIS AIRCRAFT

1 4 CHANNEL RADIO WITH 4 MICRO SER-

VOS. (WE USED 4 CHANNEL

FUTABA

RADIO WITH S3110 SERVOS AND

FUTABA

RECEIVER )

1 6” SERVO “Y” HARNESS

2 12” SERVO EXTENSIONS

1 ELECTRONIC SPEED CONTROL (WE

USED A

CASTLE CREATIONS

PHOENIX

25 BRUSHLESS SPEED CONTROL)

1 3 CELL LI-PO BATTERY (

GREAT PLANES

ELECTRICFLY 1500)

ULTRAFLY

BRUSHLESS MOTOR A/30/29

WITH 3.89 GEAR RATIO

GREAT PLANES

ELECTRIFLY PROP

ADAPTER 3MM APC LONG

APC

PROPELLER 9 X4.7 SLO FLYER

1 CA ACCELERATOR

1 1 OZ. BOTTLE CA MEDIUM GLUE

1 1/2 OZ. BOTTLE CA THIN GLUE

1 5 MINUET EPOXY

1 1/4” FOAM RUBBER

1 SHEET METAL SCREWS FOR

MOTOR(MIGHT BE REQUIRED FOR SOME
MOTOR INSTALLATIONS)

TOOLS AND SUPPLIES FOR ASSEMBLY

MODELING OR UTILITY KNIFE

WORK SURFACE (24" X48")

SMALL STANDARD & PHILLIPS SCREW-
DRIVERS

MASKING TAPE

NEEDLE NOSE PLIERS

24” RULER

FLEXIBLE STRAIGHT-EDGE

30-60-90° x 6" TRIANGLE

SOFT PENCIL

A FEW STRAIGHT OR "T" PINS

WIRE CUTTER (DYKES)

OPTIONAL HEAT GUN/COVERING IRON

ACID BRUSH

5 FT. LENGTH OF STRING

Caution:

Before starting, carefully go

over all high stress areas

(Wing bolt mounting blocks,

Firewall,etc.) with an epoxy or

wood glue to confirm all

areas are well glued.

Warnings about Lithium

Polymer batteries

NEVER charge Lithium Polymer batteries with a

charger designed for NiCd, NiMH, or any

other type of battery chemistry. Use ONLY

the chargers listed under REQUIRES or

equivalent substitutes.

Do not allow Li-Po cells to overheat at any time. Cells

which reach greater than 140° Fahrenheit

(60C) will usually become damaged and

could catch fire.

Do not charge or discharge Li-Po cells on or near

combustible materials including paper, plastic,

carpets, vinyl, leather, wood, inside an R/C

model or full size automobile.

Do not expose Li-Po cells to water or moisture at any

time.

Do not store batteries near an open flame or heater.
Do not assemble Li-Po cells or pre-assembled packs

together with other Li-Po cells or packs.

Do not allow a Li-Po battery to be left unattended dur-

ing charging or discharging.

Always store Li-Po batteries in a secure location

away from children.

Always remove a Li-Po battery if model is involved in

any kind of

crash. Carefully inspect the

battery and connectors for even the

smallest damage.

CAUTION

, cells may be hot!

Do not

allow the electrolyte to get into eyes or on

skin. Wash affected areas immediately if

they come into contact with electrolyte.

Содержание S.E.5A

















Результаты поиска

Содержание S.E.5A

Отзывы:

Бренды по названию

Популярные бренды

Lanier R/C S.E.5A, Руководство пользователя

Результаты поиска

Содержание S.E.5A

Отзывы:

Бренды по названию

Популярные бренды