Lanier R/C S.E.5A Скачать руководство пользователя страница 1

S.E.5a

Lanier R/C, INC. P.O. Box 458 Oakwood, Ga. 30566 PH 770 532 6401

© copyright 2006 Lanier R/C

Important Information:

Please inspect the plane before beginning to assemble to make sure you are happy with it. After

assembly has begun you cannot return the kit. If you find a problem before beginning to assemble the

plane you must contact us, please do not return it to the dealer. Due to temperature changes the plane

may develop some wrinkles in the covering that you will need to remove with an iron. Be sure to seal

the edges down first so that you do not cause the covering to shrink and leave exposed areas of wood.

The model is built light to ensure good flight characteristics. With the power available from the new

breed of engines, it is necessary to use throttle management in order not to overstress the airframe.

You must maintain good tight control linkage with no slop, good servos with plenty of power, and good

servo arms to protect against flutter. Sloppy linkage and over speeding the plane will cause flutter

which is not covered in the warranty. Lanier R/C is proud of the care and attention that goes into the

manufacture of parts for its model kits. The company warrants that for a period of 90 days, it will

replace, at the buyers request, any parts or material shown to the company’s satisfaction to have been

defective in workmanship or material at the time of purchase. No other warranty of any kind, expressed

or implied, is made with respect to the merchandise sold by the company. The buyer acknowledges

and understands that he is purchasing only a component kit from which the buyer will himself construct

a finished flying model airplane. The company is neither the manufacturer of such a flying model air-

plane, nor a seller of it. The buyer hereby assumes the risk and all liability for personal or property

damage or injury arising out of the buyers use of the components or the finished flying model airplane,

whenever any such damage or injury shall occur. Any action brought forth against the company, based

on the breach of the contract of sale to the buyer, or on any alleged warranty there under, must be

brought within 1year of the date of such sale, or there after be barred. This one year limitation is

imposed by agreement of the parties as permitted by the laws of the state of Georgia.

Содержание S.E.5A

















Отзывы: