background image

 

12

 

MAINTENANCE & CLEANING 

Cleaning 

WARNING: 

KEEP WATER AND SOLUTIONS OUT OF 
CONTROLS.  NEVER SPRAY OR HOSE 
CONTROL CONSOLE, ELECTRICAL 
CONNECTIONS, ETC. 

CAUTION:

 

MOST CLEANERS ARE HARMFUL TO THE SKIN, 
EYES, MUCOUS MEMBRANES AND CLOTHING.  
PRECAUTIONS SHOULD BE TAKEN TO WEAR 
RUBBER GLOVES, GOGGLES OR FACE SHIELD AND 
PROTECTIVE CLOTHING.  CAREFULLY READ THE 
WARNING AND FOLLOW THE DIRECTIONS ON THE 
LABEL OF THE CLEANER TO BE USED. 

The griddle should be thoroughly cleaned at least once a week in addition to the 
normal daily cleaning to insure against the accumulation of foreign material.  

NOTICE:

 

Any cleaner used should be marked: “SAFE ON 
ALUMINUM”. 

Electric equipment is inherently clean and sanitary, but may become unsanitary if 
dirt is allowed to accumulate on it.  Take advantage of the clean, sanitary features 
of electric equipment, give it the regular attention that it deserves the same as any 
other highly perfected machinery, to insure best results and continued high 
operating efficiency. 

 

 
 
 

CALIBRATION 

Calibration Check 

¾

 

Place thermometer or thermocouple in the center of griddle. 

¾

 

Set thermostat to 350

°

F. 

¾

 

Allow the griddle to Preheat for at least half an hour. 

¾

 

Note cycle on temperatures and cycle off temperatures for 3 cycles. (Red indicator 
light indicates when oven is calling for heat) 

¾

 

After 3 cycles average the temperature. ( Add all six temperatures and divide by 6) 

Calibration Adjustment 

¾

 

A 1/16” flat blade screwdriver with a 2” shaft is required to make adjustments on 
the thermostat. 

¾

 

Maintain the oven temperature at 350

°

¾

 

Without turning the thermostat, remove the knob. 

¾

 

Locate the adjustment screw at the base of the shaft and insert the screwdriver. 

¾

 

Grasp the shaft and turn the screwdriver.  Counter clockwise to increase and 
clockwise to decrease (1/8 of a turn will move the temperature 5-7 

°

 in either 

direction). 

¾

 

Reinstall the oven knob and recheck the oven temperature. 

 

 

 

Содержание 160TT

















Отзывы: