background image

1-1

Walking Tandem Instructions

Walking Beam Disassembly

1.

Loosen lug nuts on tires and remove both inner and 
outer tire and wheel assemblies from the walking 
tandem.

2.

Remove walking tandem from axle leg. Remove 
1-1/2” nut and pull pin out to let the walking tandem 
assembly come loose. A new pin is supplied with the 
update, but do not swell the end of the threads to 
where they will not go through the axle leg by 

hammering

 on them. Use caution as the walker with 

the hubs installed is heavy once the pin comes out.

3.

Remove the grease zerks from the walking beam.

4.

With the appropriate driver, remove the steel insert 
bushing from the walking beam 

(See Figure 1-1.)

 

Penetrating oil can be sprayed down the zerk holes to 
aid in removal.The steel bushing is split on the side 
with the zig zag edge and can be carefully cut with an 
oxy/acetylene torch on the other to remove the 
bushing if necessary.

CAUTION

5.

Clean out all rust and scale left in the inner bore with 
a honing tool of some sort. We recommend a ball 
style hone.

6.

With the 5/16-24 tap provided, finish tapping the 
grease zerk holes so the set screw will go clear 
through to lock the bushing into place. They were 
tapped almost all the way through when produced, 
but not completely so the threads need to be 
completed to the bottom of the hole. If the walking 
tandem has 1/4-28 tapped hole for the zerk, a 17/64 
drill bit has been supplied to drill out the hole and 
retap it to 5/16-24 threads.

Use care in removing the bushing to not damage 
the inner bore of the walker as the new bushing 
needs to be installed by hand.

Содержание F-847-0316









Отзывы: