Landoll Brilllion Till'N Seed BPSB-8 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 76

background image

MAINTENANCE

F-1097-2305

4-9

TABLE OF CONTENTS

Figure 4-11: Rotor Drive Blade Repair - RH Side

17. Repair Drive Rotor as necessary.

See Figure 4-8.

18. Re-Assemble Drive Rotor into the Frame. 1.523 Shaft

is on the left and 1.776 Shaft is on the right. Orient the
Bearing Shield cup outward. Place the appropriate
Bearing Shield and 11ga Washer on the Drive Rotor
Shafts.

See Figures 4-10

19. Raise one end of the Drive Rotor with a floor jack and

add a block. Raise the other end of the Drive Rotor
and add a block. Continue incrementally in this
fashion until the Drive Rotor is positioned inside the
frame so that the Bearings can be mounted onto the
Frame End Plates. Ensure that the Bearing Shields
are inside the frame and were not damaged during
this process.

20. Apply anti-seize on the Drive Rotor Shafts. Slide the

RH Bearing onto the Rotor Shaft and attach the
Bearing to the Frame End Plate. Slide the LH Bearing
onto the Rotor Shaft. Attach the Bearing to the Frame
End Plate Rear Top Hole and Frame End Plate Front
Bottom Hole with 1/2-13 x 1-1/4 Carriage Bolts. Orient
the Chain Shield with the cutouts to the top. Assemble
the Chain Shield along with the Bearing to the Frame
End Plate Front Top Hole and Frame End Plate Rear
Bottom Hole with 1/2-13 X 1-1/2 Carriage Bolts.
Secure with Flat Washers, Lock Washers and Nuts.

21. Install Seed Box #60 Drive Sprocket and 3/8 Key onto

the LH Drive Rotor Shaft.

22. Install Seed Box #60 Drive Chain. Adjust Chain

Tension.

See “Chain Tension” on page 4-12.

23. Install Thrust Plate onto the RH Frame End Plate and

place 3/16 Thick Washers onto the Drive Rotor Shaft.

24. Install LH and RH Swing Arms onto Drive Rotor and

Tillage Rotor Shafts.

25. RH side, place a 1.785 x 11ga Washer on the Drive

and Tillage Rotor Shaft. Install #80-2 Sprockets and
1/2" Keys onto Rotors. Larger Sprocket is on the Drive
Rotor.

26. RH side, secure the Drive and Tillage Rotors by

installing 3/4-10 x 2 Bolts, Lock Washers, and 3/4 x 3
x 3/8 Washers on the end of the Rotor Shafts.

27. LH side, secure the Drive and Tillage Rotor Shafts by

installing 3/4-10 x 2 Bolts, Lock Washers, 3/4 x 2-1/16
x 3/8 Washers, and Flat Top Washers on the end of
the Rotor Shafts.

28. Install Rotor #80-2 Drive Chain. Adjust Chain

Tension.

See “Chain Tension” on page 4-12.

29. Install chain access Cover to the RH Swing Arm.
30. Install Rotor Drive Chain Shield.
31. Insert the Gauge Wheel Hub and Spindle into the

Gauge Wheel Arm. Secure with 3/8-16 x 2-1/2 Bolts
and Locknuts.

32. Attach LH and RH Rockshaft Links to the Swing Arms

with 5/8-11 x 1-3/4 Bolts and Lock Washers.

33. Fill LH and RH Tillage Rotor Air Shocks with air.

“Air Shock” on page 3-6.

Rockshaft Link

Gauge

Wheel Arm

Bolt,

3/4-10 x 2

Washer,

Lock 3/4

Washer,

3/4 x 2-1/16 x 3/8

Washer,

Flat Top

LH Swing

Arm

Drive

Sprocket,#60

Bearing,1.535

Chain

Shield

Drive Rotor

Bearing

Shield,1-1/2

Washer,

1.547 ID x 11ga

Carriage Bolt,
1/2-13 x 1-1/4

Front

Key,3/8

«
...
59
60
61
62
63
...
»

Содержание Brilllion Till'N Seed BPSB-8













































































Отзывы:

Нет отзывов

Похожие инструкции для Brilllion Till'N Seed BPSB-8

Бренд: Panasonic Страницы: 30

Бренд: Major Страницы: 52

Aspect Q-CARD 100-4T

Бренд: idi Страницы: 38

Бренд: popular Страницы: 27

Бренд: Irwin Страницы: 2

Бренд: Mobiak Страницы: 15

MT765 Challenger

Бренд: Fast Страницы: 31

Бренд: Delfield Страницы: 2

Vetter QuickStrut

Бренд: Idex Страницы: 14

Бренд: GGM gastro Страницы: 3

Бренд: Wartmann Страницы: 56

Бренд: PALAZZANI Страницы: 131

VEX-WPCR Series

Бренд: Exitronix Страницы: 4

ADVANTAGE 78400-117

Бренд: Medivators Страницы: 12

CAPE HORN EC202B

Бренд: SMP Playgrounds Страницы: 22

INTIMIDATOR 15XPC

Бренд: Bandit Страницы: 112

Бренд: GYM form Страницы: 40

Бренд: ALLSPEEDS Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды