Landoll BRILLION TURFMAKER II SL Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 100

background image

ASSEMBLY

9K998

2-21

Electric Clutch Kit

IMPORTANT

At no time use high pressure water or air to clean the
Electric Clutch as damage could occur.

1. Verify that the Electric Clutch has 1/8” clearance

between the Clutch Housing and Rubber Bumper
Stop. Improper clearance may prevent the Clutch
from engaging or disengaging.

See Figure 2-26.

2. Connect Clutch Harness to Clutch Lead and route

along Frame and Drawbar/3Pt Hitch. Secure to
Frame and Drawbar/3Pt Hitch or with Hydraulic
Hoses and Warning Lamp Harness with Tie Wraps
and Adhesive Mounting Plates.

See Figure 2-27.

3. Install Clutch Switch on Tractor in a convenient

location with the Hook and Loop included or other
type of mount (not included).

4. Connect Harness to power source and secure.
5. Check Electric Clutch Operation. The Electric Clutch

will disengage when power is applied. (Clutch will
make a clicking sound). Set Seeder on the ground
and drive a short distance while turning Toggle
Switch to “Seed” and “No Seed”. The Seed Shaft will
stop rotating when Toggle Switch is turned to “No
Seed” Position.

6. Turn Toggle Switch to “Seed” Position when Seeder

is not used to shut off power to prevent possible
overheating of Clutch Coil.

Electric Clutch Attributes:

• The Electric Clutch is controlled by a Toggle Switch

on the Clutch Switch Box that is mounted to the
Tractor.

• The Electric Clutch is disengaged when power (12

Volts) is applied. If there is a power failure or
electrical problem, the Seeder will continue to
operate, so the machine must be raised to stop
seeding.

• Seed Shafts will not rotate when the machine is

backed up.

• The Clutch Switch Box contains a 5 Amp Time-Delay

Fuse.

•

The Electric Clutch must be disengaged (power
applied) when Seed Shafts are turned manually for
Calibration

.

Figure 2-26: Clutch Clearance

Figure 2-27: Clutch Harness

*DS

%XPSHU%ROW

5XEEHU%XPSHU

6WRS

(OHFWULF

&OXWFK

&OXWFK/HDG

(OHFWULF

&OXWFK

&OXWFK+DUQHVV

+\RVHV

«
...
35
36
37
38
39
...
»

Содержание BRILLION TURFMAKER II SL





































































































Отзывы:

Нет отзывов

Похожие инструкции для BRILLION TURFMAKER II SL

Бренд: Falcon Страницы: 52

Бренд: YSI Страницы: 70

Бренд: jcb Страницы: 41

Бренд: Ace Страницы: 17

Бренд: ACE INSTRUMENTS Страницы: 33

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: TapFlo Страницы: 35

Бренд: DANA Страницы: 8

Бренд: 2E Страницы: 6

Precision2 HP2 Series

Бренд: B-K lighting Страницы: 6

Бренд: Zero Hand Truck Страницы: 38

Бренд: B-K lighting Страницы: 3

Бренд: Bang & Olufsen Страницы: 2

Бренд: Olympus Страницы: 56

ThermoTweez Handpiece TT-65

Бренд: Pace Страницы: 14

Бренд: Samson Страницы: 2

Бренд: Mako Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды