manualshive.com logo in svg

Landoll Brillion SL10, Руководство оператора

Поделиться
Скачать
Landoll Brillion SL10 Скачать руководство пользователя страница 26

2-12

1P342-0621

ASSEMBLY

Warning Lamp Installation, 12FT

NOTE

12FT Drawbar model is shown, 3-PT models similar.

1. Attach both Red Lamps to the ends of the Light Bar 

with 1/4-20 x 1-1/4 Bolts and Locknuts. 

See 

Figure 2-17.

2. Attach longer Light Bracket to the Transmission  

located on the left side of the Seeder, with 3/8-16 x 
1-1/4 Bolts, Lock Washers and Nuts. 

3. Attach Amber Lamp to the outside of the Light 

Bracket with 1/4-20 x 1-1/4 Bolts and Locknuts.

4. On the right side of the Seeder, attach the shorter 

Light Bracket to the Angle Bracket with 1/2-13 x 1-1/4 
Bolts, Lock Washers and Nuts. 

5. Attach an Amber Lamp to the upper portion of the 

Light Bracket with 1/4-20 x 1-1/4 Bolts and Locknuts.

6. Attach the Light Module to the Module Bracket with 

1/4-20 x 1-1/2 Bolts and Locknuts. 

See Figure 2-16.

7. Lay out the Lamp Harness, noting that the 

connectors marked with Green Tape is Right Side 
and Yellow Tape is Left Side.

8. Connect the Lamp Harness into the Light Module, 

route the plugs with Green Tape along the front right 
side of the frame. Route the 3 prong cord up the 
Light Bar and plug into the Red Lamp. Continue 
routing the 2 prong cord along the front of frame, up 
the outer Light Bracket and plug it into the Amber 
Lamp.

9. Repeat for the Left Side (Yellow Tape).
10. Connect the 7-Pin Harness into the Light Module, 

then route the harness along the Drawbar with the 
Hydraulic Hoses and secure with tie wraps.

11. Bundle and secure excess cord to the Module 

Bracket with tie wraps. Secure cords along frame 
and Drawbar using Adhesive Mounts and tie wraps.

NOTE

If equipped with optional Electrical Clutch, install, route 
and secure Electric Clutch Harness with the Warning 
Lamp Harness.

IMPORTANT

All Harnesses must be firmly attached to Machine 
Frame members or Hydraulic Hoses so they do not 
sag or become torn loose by field debris.

12. Attach the SMV sign to the SMV Mount located on 

the center on the Light Bar with 5/16-18 x 1 Bolts, 
Flat Washers, and Locknuts.

13. Attach the Connector Holder to the Drawbar Hose 

Holder or 3-PT Hitch with 1/4-20 x 1 Bolts, Flat 
Washers, and Locknuts.

NOTE

The 7-Pin Plug on the other end of the 7-Pin Harness 
connects to the Tractor Socket when in use. When not in 
use, it can be stored in the Connector Holder on the 
Drawbar Hose Holder or 3-PT Hitch. Allow enough 
Harness length to reach Tractor Socket and roll or fold up 
excess and secure to Drawbar Hydraulic Hoses or 3-PT 
Hitch.

Figure 2-16:  Light Module and Bracket

Module Bracket

Light Module

Locknut,1/4-20

Bolt,

1/4-20 x 1-1/2

Содержание Brillion SL10













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды