manualshive.com logo in svg

Landoll Brillion PAT 10, Руководство оператора, Страница: 21 / 38

Поделиться
Скачать
Landoll Brillion PAT 10 Скачать руководство пользователя страница 21

F-948R0

3-1

Chapter 3

Operation

DANGER

WARNING

DANGER

DANGER

CAUTION

Operation of the Aerator

This chapter will cover the basic operation and 
procedures for the Landoll Brillion Aerator. Be sure to 
read and understand the Safety Procedures and 
Cautions starting on 

page 1-1

. 

Aerator Preparation

1.

Prior to operating the Aerator, inspect it thoroughly 
for good operating condition.

2.

Replace worn or missing parts.

3.

When the machine is new, check the bolt tightness 
after a few hours of operation. Tighten any loose nuts 
or bolts. Check the lift wheel lug bolts daily.

4.

Check the lift wheel tire inflation. Inflate all tires 
equally to avoid side draft. Follow the tire 
manufacturer’s recommended pressures listed on the 
sidewall of the tires.

Attaching to the Tractor

1.

Align the tractor drawbar with the machine. Raise or 
lower the hitch, as needed, using the jack. Attach the 
unit with proper size hitch pin.

 

2.

Attach safety chain to tractor allowing plenty of 
movement for turning both directions. The safety 
chain should latch securely to prevent it coming 
loose. 

See Figure 1-2.

3.

Always swing the jack to the up position and pin it 
before setting the machine in motion. 

4.

Clean all hydraulic couplings and attach to the 
tractor.

5.

Fully extend the hydraulic lift cylinder. Secure 
transport lock pin in the lock position. 

See 

Figure 3-4.

6.

Plug in the 7 pin connector for the lights.

• Make sure the tractor has a good clean receptacle, 

free of dirt and corrosion.

• Make sure the 7 pin connector is inserted ALL the 

way in. With tighter fitting pins, operator may think the 
connector is all the way in, but really isn’t.

• Make sure the tractor receptacle cover latches over 

the keyway on the 7 pin connector to hold the 
connector in place.

• If lights don’t seem to work right, check the above 

items to make sure there is a good connection.

Never allow anyone to ride on the Aerator at any 
time. Allowing a person to ride on the machine 
can inflict serious personal injury or death to that 
person.

All hydraulically elevated equipment must have 
cylinder lockout installed or be lowered to the 
ground, when servicing or when equipment is 
idle. Failure to take preventive measures against 
accidental lowering can result in serious 
personal injury.

Always lock the tractor drawbar in the center 
position when transporting the unit. Failure to do 
so can result in serious injury or death and cause 
damage to the equipment.

When transporting the unit, place cylinder 
lockout pin in the transport lock position after 
fully extending the cylinder. Insert the lockout pin 
to secure the cylinder lockout. Failure to lockout 
the cylinder can cause the unit to settle during 
transport, which can result in serious injury or 
death and cause damage to the equipment.

When transporting farm implements on public 
roads, it is the responsibility of the operator to 
abide by state and local laws concerning wide 
loads, speed, safety emblems and safety lighting 
equipment. Drive at safe speeds, particularly 
when rounding corners, crossing rough ground 
or driving on hillsides, to prevent tipping the 
tractor.

Содержание Brillion PAT 10







































Отзывы:

Нет отзывов