manualshive.com logo in svg

Landoll Brillion PAT 10, Руководство оператора, Страница: 18 / 38

Поделиться
Скачать
Landoll Brillion PAT 10 Скачать руководство пользователя страница 18

2-8

F-948R0

ASSEMBLY

LED Lamp and Harness Installation

1.

Attach the four Light Brackets to the Frame Tube by 
placing a Strap under the Tube and securing with 
1/2-13 x 8-1/2 Bolts, Flat Washers and Locknuts. 

2.

Place an Amber LED Lamp inside a Tube Light 
Shield and attach them to each outer Light Brackets 
front two holes with 1/4-20 x 1-1/2 Bolts and 
Locknuts. Attach the Decal Bracket to the Light 
Brackets, Shield and Lamp rear two holes with two 
1/4-20 x 1-3/4 Bolts and Locknuts.

3.

Install a Red LED Lamp and a Decal Plate onto each 
inner Light Bracket with four 1/4-20 x 1-1/2 Bolts and 
Locknuts.

4.

Attach the Flasher Control Module to the RH side of 
the Frame Center Mast Plate with two 1/4-20 x 2 
Bolts and Locknuts.

IMPORTANT

Cords are marked Left or Yellow/Right or Green

5.

Raise the machine if not done previously.

6.

Layout the LED Lamp Harness and attach the 
harness to the Light Module. 

7.

Route the left and right 3 plug cord along the frame 
and connect to each Red LED Lamp.

8.

Route the remaining left and right 2 plug cords along 
the left and right frame and connect into each Amber 
LED Lamp.

9.

Layout the 7 Pin Harness and attach the harness to 
the Light Module.

10. Route the 7 Pin Harness across the frame and along 

the drawbar tube and over to hitch point.

11. Adjust the LED Lamp angle so that the lamp is 

vertical (perpendicular) to the ground when the 
Aerator is in the transport position. Whether the 
Aerator is towed behind a tractor or a companion 
tool, the Light Mount Bracket provides lamp 
adjustment for higher or lower drawbar heights, 
ensuring that the lamp will always be vertical 
(perpendicular) to the ground and clearly viewable 
from the front and rear of the machine. 

See 

Figure 2-8.

12. Tighten all hardware.

13. Bundle and secure any excess cord with tie straps. 

Ensure 7 pin harness is secured, so it is not pinched 
when machine is raised or lowered.

NOTE

All wires must be firmly attached to machine frame 
members so they do not sag or become torn loose by 
field debris.

14. Attach the SMV Sign to the center frame weldment 

using two 5/16-18 x 1 Bolts, Flat Washers and 
Locknuts

.

15. Apply the reflector decals to the Decal Plate Mounts. 

The amber reflector decals should be front facing on 
the outer Decal Plate Mounts. The red reflector 
decals and orange decals should be rear facing on 
both the inner and outer decal plate mounts.

Figure 2-8: LED Lamp Adjustment

Pivot Lamps so that they are
 vertical to the ground when
    Drawbar is in Transport

Содержание Brillion PAT 10







































Отзывы:

Нет отзывов