background image

2-1

Chapter 2

Assembly

CAUTION

WARNING

NOTE

Refer to the repair parts manual 7D524 for identification 
of parts and for the approximate relationship of the parts 
in assembly.

To ensure alignment of assemblies, 

leave the nuts 

l

oose until completion 

of final assembly. Use lock 

washers or flat washers as specified. Spread all cotter 
pins.

After completion of final assembly, tighten all nuts
evenly 

to prevent misalignment, distortion or binding.

Tighten all screws and nuts to the recommended torques.

Using blocks or other supports, block up the Frame 
approximately 36”. Be sure that it is secure and cannot 
topple. 

IMPORTANT

• If pre-assembled parts or fasteners are temporarily 

removed, remember where they go. It is best to keep 
parts separated.

• Check that all working parts move freely, bolts are tight 

and cotter pins spread.

• Refer to the Torque Table for proper torque valves. 

Note the different torque requirements for bolts with 
lock nuts. 

See Page 4-1

.

“Left” and “Right” refer to directions seen as if standing 
behind the machine and facing in the direction of forward 
travel.

Main Frame Assembly

1.

Place the frame on blocks at least 36-42 inches high 
for the assembly of the machine. 

2.

See Figure 2-2 

for the dimensional location of the 

Upper and Lower Hitch Brackets.

3.

Assemble Upper Hitch Bracket to the center of the 
Front Frame Tube. Slide Upper Hitch Bracket Plate 
in the slot of the Upper Hitch Bracket and under the 
Front Frame Tube. Secure with 5/8-11 x 6 Bolts and 
Lock Nuts. 

See Figure 2-1.

4.

Place 1-5/16 x 2-1/8 spacer between the top holes of 
the Upper Hitch Bracket and place the LH and RH 
Braces on either side of the Bracket. Insert 1-8 x 6 
Bolt and secure with Lock Nut. Install braces to the 
rear of the Frame with 3/4-10 x 2-1/2 Bolt, 
Lockwasher and Nut.

5.

Assemble LH and RH Lower Hitch Brackets to the 
Front Frame Tube. Secure with 5/8-11 U-Bolts and 
Lock Nuts. 

6.

Determine the category of tractor and Length of 
Shank that will be used and install the Upper and 
Lower Hitch pins into the Hitch Brackets.

 See 

Figures 2-1, 2-3 and 2-4.

Tighten all hardware to the recommended torques. 

See 

Page 4-1

.

Manual Storage Canister

Install the Manual Storage canister to the frame with 
Hose Clamps. 

See Figure 2-1

.

SMV Sign

Attach the SMV Mount about 4 inches left of center on 
the rear Frame Tube with 1/2-13 U-Bolt and Flange Lock 
Nuts. 

See Figure 2-1

. Install SMV Sign to Mount with 

5/16-18 x 1 Bolts, Flat Washers and Lock Nuts.

Do not work on or under this machine unless 
securely 

blocked and supported by a hoist or 

tractor or by other sufficient means.

Do not attempt to lift heavy parts (such as the 
frame, rock shaft, and pull hitch) manually. Use a 
hoist or a fork lift to move these parts into 
position.

Содержание Brillion CPP7















































Отзывы: