Landoll 876-30 Скачать руководство пользователя страница 57

Страница: 57 / 60

TROUBLESHOOTING GUIDE

5-3

ROCKS JAMMING IN END OF REEL
AND LOCKING UP REEL

Reel blade too long

Cut 1-1/2" off the end of reel blade.

Reel angle wrong for terrain

Cut blade off at angle toward rear of blade

to provide a relief area for rocks.

HARROW PLUGGING

Improperly set harrow

Set according to operating instructions

(See “Harrow Adjustment” on
page 4-7.)

WINGS FOLDING TOO FAST

Restrictor elbows not installed

Check to make sure restrictors are

installed per assembly instructions.

Idle tractor when folding.

Turn tractor hydraulic flow down.

Engage hydraulic valve. Hold fully
engaged until folded.

MACHINE RUNNING DEEP TO ONE
SIDE

Distance from frame to axle of gauge
wheels differ

a. Set all depth stops the same.

b. Raise machine until all cylinders are

fully extended.

c. Measure cylinders from pin to pin.

Verify that all cylinders are same
length.

If measurements are not the same,

see “Hydraulic Lift Installation
(876-30, 876-35, 876-40-C)” on
page 3-9 and “Hydraulic Lift
Installation (876-40-H)” on page 3-11

to readjust cylinder length.

Wing cylinders may need to vary in length

from main cylinders, per soil conditions.

Check that tires are same size and
pressure is correct.

Check for hydraulic leakage and repair.

CYLINDERS BROKEN IN TRANSPORT

Machine not properly secured during
transport

Use transport locks and let machine down

on locks during transport

(See

“Transport” on page 4-3.)

PROBLEM

PROBABLE CAUSE

SOLUTION

Содержание 876-30





























































Результаты поиска

Содержание 876-30

Отзывы:

Похожие инструкции для 876-30

Бренды по названию

Популярные бренды

Landoll 876-30, Руководство оператора

Результаты поиска

Содержание 876-30

Отзывы:

Похожие инструкции для 876-30

Бренды по названию

Популярные бренды