Landoll 876-30 Скачать руководство пользователя страница 56

Страница: 56 / 60

5-2

F-143-0211 Edition

TROUBLESHOOTING GUIDE

SHANKS NOT STRAIGHT UP AND
DOWN ON FRAME OR HAVE
EXCESSIVE WEAR

Excessive wear at pivot bolt

Replace bolt-on shank holder, if needed.

Replace bushing, if needed.

SHANK SPRINGS BREAKING

Spring pivot bolt too tight

Spring pivot bolt must be loose enough to

allow spring plug to pivot so spring is
not forced to bend.

SCREW IN TOP OF SPRING BREAKING

Lock nut should be tightened against
shank bracket instead of spring plug

Verify that there are three threads between

lock nut and spring plug.

PLUGGING IN SHANK AREA

Shank placement not according to
specifications

Check shank placement against

Figures

2-1 through 2-6.

Ground too wet

Wait until ground conditions are proper for

tillage.

REEL VIBRATING

Rear of machine too deep

Level machine by turning radius rod.

Running machine too slow

Machine needs to be pulled at least 5.5

mph.

REEL COMING LOOSE IN FIELD

Reel bearing lock collars mounted on
wrong side of reel

Mount lock collars on side of reel toward

center of machine.

Lock collars tightened in wrong
direction. Lock in direction of reel
rotation.

REEL NOT MOVING SOIL ADEQUATELY

Reel mounted backwards

Mount again per assembly instructions

(See “Reel Assembly Installation”
on page 3-18.)

Running machine too slow

Machine needs to be pulled at least 5.5

mph.

Machine not level

Adjust radius rod to level machine.

PROBLEM

PROBABLE CAUSE

SOLUTION

Содержание 876-30





























































Результаты поиска

Содержание 876-30

Отзывы:

Похожие инструкции для 876-30

Бренды по названию

Популярные бренды

Landoll 876-30, Руководство оператора

Результаты поиска

Содержание 876-30

Отзывы:

Похожие инструкции для 876-30

Бренды по названию

Популярные бренды