3-8
F-832-2307
Manual Leveler
1.
Using the manual leveler, screw the 71” leveler tube
onto the leveler screw assembly
.
Initially leave approximately 1” of threads visible,
further adjustment may be required. Rotate the tube
so that the zerk hole in the threaded end is pointing
upward.
2.
Install the manual leveler handle assembly into the
front end of the leveler tube and fasten with two 5/8 x
3-1/2 bolts and 5/8 lock nuts
. Insert a
flange bearing into the flat side of each leveler cross
bracket. Slide the brackets over each side of the
manual leveler cross and secure with 1n flat washers
and 5/16 x 2-1/2 spring pins.
3.
Attach the leveler cross brackets to the top of the
leveler L link using 3/4 x 3-1/2 bolts and 3/4 lock nuts.
4.
Install a 1/4 zerk in the threaded end of the leveler
tube.
Hydraulic Leveler (Option)
1.
Thread a 1-1/2 nut onto the leveler screw assembly
Initially leave approximately ” of
threads visible between the 1-1/2 nut and the leveler
spring nut. Further adjustment may be required.
2.
Thread the leveler tube onto the leveler screw
assembly until it contacts the 1-1/2-6 hex nut. Rotate
the tube so the grease zerk hole in the threaded end
points upward.
3.
Slide the leveler cross over the front end of the
leveler tube
4.
Insert the 3-1/2 x 6 cylinder into the front end of the
leveler tube and pin using two 5/8 leveler pins. Rotate
the cylinder so the hydraulic ports point to the left
side of the implement.
5.
Slide the leveler cross up to the cylinder and secure
with 1/2 x 2 bolts and hex lock nuts. Install the bolts
from the back of the leveler cylinder cross, pointing
forward for proper operating clearance. The indicator
window of the leveler cylinder cross should point to
the right side of the implement.
6.
Insert a flange bearing in each leveler cross bracket.
Install the plastic wear flange bearing from the tube
side of the bracket.
7.
Slide the leveler cross brackets onto the leveler
cylinder cross and secure with washers and 5/16 x
2-1/2 spring slotted pins.
8.
Attach the leveler cross brackets to the top of the
leveler L link using 3/4 x 3-1/2 bolts and 3/4 lock nuts.
9.
Install grease 1/4 zerk in the threaded end of the
leveler tube and the leveler cylinder cross.
10. With a 1/2 x 2 bolt and 1/2 lock nut, attach the leveler
indicator gauge to the leveler cross. Do not over
tighten this screw, as the indicator gauge must be
free to pivot about this joint. Attach the level indicator
decal to the front of the level indicator gauge.
11. Rotate the 71” leveler tube so the cross-hole for the
level indicator rod is horizontal. Wrench-flats are
provided at the threaded end of the leveler tube to
make this adjustment. Secure the 1-1/2 nut to
prevent the leveler tube from rotating further.
12. Insert the threaded end of the leveler indicator rod
through the leveler tube cross-hole and the other rod
end through the bottom leveler indicator hole. Secure
the indicator rod with a 3/8 lock nut.
13. Install 90° elbow w/1/32” restrictor fittings in the
leveler cylinder.
NOTE
These are smaller restrictor fittings than those used in
the fold system.
14. Install (4) #8 adapter fittings into each port of check
valve
.
15. Install check valve to hose clamp holder on hitch
using 3/8 x 2 bolts and 3/8 lock nuts. Note that ports
C1/C2 go to the 3-1/2 x 6 cylinder and ports V1/V2
go to the tractor
16. Assemble 56” and 54” hoses from the 3-1/2 x 6
cylinder to the check valve,
17. Attach (2) 140” hoses from the check valve to the
tractor.
Figure 3-4: Check Valve Placement
10. Wrap hydraulic leveler hoses with black hose wrap
.
C2
C1
V2
V1
3-1/2 X 6
CYLINDER
HOSE HOLDER
CLAMP
CHECK VALVE
W/ ADAPTERS
HOSE, 140”
HOSE, 56”
HOSE, 64”
Содержание 6231
