Landoll 5530 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 70

background image

OPERATION AND MAINTENANCE

4-31

Figure 4-32: Opener Scraper Adjustment

Opener Scraper Adjustment

1.

The opener is equipped with a scraper to keep the
inside surfaces of the opener blades clean. In dryer
conditions, the scraper can be adjusted farther away
from the opener blades for greater clearance. In
wetter conditions, it will be necessary to adjust the
scraper blade closer to the opener blade.



CAUTION

2.

To adjust the scraper blade, loosen the 1/2-13 hex
flange spiralock nut holding the blade, and slide the
blade up or down to achieve the desired clearance

(See Figure 4-32.)

Retighten the 1/2-13 hex flange

spiralock nut. Carefully rotate the opener blades to
make sure the blades will turn freely and not drag on
the scraper.

3.

A properly maintained opener blade pinch point will
reduce the amount of soil that enters between the
opener blades. This will in turn allow the scraper to
operate in a cleaner environment and reduce scraper
wear.

AIR OPENER ASSEMBLY

OPENER
SCRAPER

1/2-13 HEX FLANGE
SPIRALOCK NUT

DISC BLADE ASSEMBLY

5530scraper

Opener blades are very sharp. Use gloves when
working around opener blades.

«
...
49
50
51
52
53
...
»

Содержание 5530







































































Отзывы:

Нет отзывов

Похожие инструкции для 5530

Бренд: Olympus Страницы: 86

Бренд: Parker Research Corp Страницы: 3

Бренд: S.I.T.A. Страницы: 32

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Konica Minolta Страницы: 32

Бренд: Mackie Страницы: 18

Бренд: Mackie Страницы: 2

Бренд: Mackie Страницы: 8

Бренд: Mackie Страницы: 7

Бренд: L-Acoustics Страницы: 5

Monkey Jump MM00125

Бренд: M&M Страницы: 2

Бренд: Yamaha Страницы: 45

Бренд: Garmin Страницы: 41

Evo TM/TSV2 Awning Wall Set

Бренд: Zempire Страницы: 2

Бренд: GERATHERM Страницы: 40

Бренд: Stanton Страницы: 13

MobilGate - 128c

Бренд: SeaSoft Страницы: 11

Бренд: Jandy Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды