Landoll 5530 Скачать руководство пользователя страница 68

Страница: 68 / 70

5-2

F-524-0410 Edition

TROUBLESHOOTING GUIDE

SECTIONS PLANTING AT DIFFERENT
RATES

Seed rate adjustment not the same on all
sections

Adjust seed rate.

Drive types (sprocket ratio) not the same
on all sections

Change to same drive type on all sections.

Seed meter out of adjustment

Reset seed meters.

Seed rate adjustment handle out of
adjustment

Reset seed rate adjustment handle.

Opener seed tube plugged

Clean out seed tube

Broken seed meter

Allows excessive seeding - repair seed

meter.

UNEVEN SEED SPACING

Excessive field speed

Reduce field speed.

Unclean seed

Use clean seed

Build up of seed treatment in seed cup

Clean out seed meters

Seed tubes sagging

Replace seed tube

Drive type (sprocket ratio) too slow

Use faster drive type and readjust seed

meter opening.

Plugged opener seed tube

Clean out bottom of seed tube.

OPENER DISCS NOT TURNING FREELY

Opener plugged with mud/dirt

Clean opener.

Scraper set too tight

Adjust scraper

(See “Opener Scraper

Adjustment” on page 4-31.)

Soil control strip set too tight against
opener blades

Adjust soil strip

Soil strip plugged with residue

Adjust soil strip closer to blade, move

metal backing strip away from edge of
soil strip

(See “Opener Soil Strip

Adjustment” on page 4-32.)

PRESS WHEELS NOT COMPACTING
THE SOIL AS DESIRED

Opener down pressure set too low

Increase air system pressure on row units

(See “Air System Pressure” on
page 4-11.)

Incorrect press wheel depth adjustment

Reset press wheel depth adjustment

(See

“Opener – Press Wheel Adjustment”
on page 4-30.)

PRESS WHEEL OR OPENERS
PLUGGING

Backed up with openers in the ground

Clean out opener and press wheels and

check for damage.

Scraper worn or not adjusted correctly

Replace or adjust scraper

Opener blades worn, pinch point too wide

Reset pinch point, replace worn out

blades.

Planting conditions too wet

Wait until drier weather

Opener bearing failure

Replace opener bearings

AIR SPRING LEAKING AIR

Air spring not set all the way forward or
backward in adjustment slots

Replace and reposition air spring

Operating with too low air pressure

Minimum air system pressure is 15 psi

(See “Air System Pressure” on
page 4-11.)

PROBLEM

PROBABLE CAUSE

SOLUTION

Содержание 5530







































































Результаты поиска

Содержание 5530

Отзывы:

Похожие инструкции для 5530

Бренды по названию

Популярные бренды

Landoll 5530, Руководство оператора

Результаты поиска

Содержание 5530

Отзывы:

Похожие инструкции для 5530

Бренды по названию

Популярные бренды