Landoll 2211 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 74

background image

ASSEMBLY INSTRUCTIONS

3-25

Figure 3-22: Hitch Hose Clamps and Color Designation

Hydraulic Installation

NOTE

Refer to Figures 3-18 through 3-21 for wheel lift, disc
gang lift, and wing fold hydraulic diagrams. See Figure
3-23 for routing of hydraulic hoses on 2211-09 and -11
models.

1.

Install the manifold(s) to the manifold bracket on the
frame using 1/2-13 x 3-1/2 hex head cap screws and
hex lock nuts.

2.

Install fittings into manifolds according to

Figures

3-18 through 3-21.

3.

Install wheel lift and disc gang lift system hoses per

Figures 3-18, 3-19, and 3-20.

4.

Install wing fold system hoses (2211-13 and -15
models) per

Figure 3-21.

5.

Hold each system of hoses in place using 3/8-16 x 3
(2211-09 and -11 models) or 3/8-16 x 4 (2211-13 and
-15 models) hex head cap screw, hose clamps, and
hex lock nut

(See Figure 3-22.)

6.

Install steel plugs in any remaining open manifold or
valve ports.

7.

Install hose wraps around system hoses per hose
identification decal near hose couplers, putting both
hoses inside wrap

(See Figure 3-22.)

Note that no

yellow hose wrap is used on rigid models.

Figure 3-23: 2211-09 and -11 Hydraulic Hose Routing

3/8-16 X 3 OR
3/8-16 X 4 HEX
HEAD CAP SCREW

HOSE CLAMPS

3/8-16 HEX LOCK NUT

2210 hitch hose clamps

DISC GANG LIFT
HOSES TO
TRACTOR

RUN HOSES THROUGH
LIFT BEARING MOUNTS

NOTE: RADIUS ROD
REMOVED FOR CLARITY

hyd hose routing

«
...
39
40
41
42
43
...
»

Содержание 2211











































































Отзывы:

Нет отзывов

Похожие инструкции для 2211

Бренд: Makerfire Страницы: 10

Бренд: YardCraft Страницы: 17

Бренд: Obdstar Страницы: 10

Бренд: Ecco Страницы: 2

Бренд: Landoll Страницы: 94

Бренд: Banfer Страницы: 6

Бренд: Cadex Страницы: 300

Бренд: Ocmis Irrigazione Страницы: 100

Бренд: Ultimate Healthcare Страницы: 2

Бренд: Ultimate Healthcare Страницы: 40

MIAMI J ADVANCED

Бренд: Össur Страницы: 35

Бренд: Össur Страницы: 38

Бренд: Össur Страницы: 8

Бренд: Össur Страницы: 72

Бренд: Össur Страницы: 76

Miami Lumbar Posteo

Бренд: Össur Страницы: 45

Бренд: Össur Страницы: 29

Icelock Clutch 211

Бренд: Össur Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды