Landoll 2130 Скачать руководство пользователя

Страница: 82 / 83

BACK ROW OF SHANKS PLUGGING WITH
RESIDUE

Heavy residue:

install optional offset shank mounts

to stagger back row of shanks. See "Offset Shank
Mount Installation" on

page 3-27

SHANKS NOT PENETRATING

Unit not level:

level unit front to rear. See "Leveling

(Front To Rear)" on

page 4-6

Excessive coulter depth

: reduce depth

Points worn:

install new points.

WHEEL BEARING FAILURE

Triple-lip seals not installed correctly:

install seals

with the lips pointing outward away from the hub.

HYDRAULIC - COULTER OR WHEEL LIFT
CYLINDERS
NOT FULLY EXTENDING

Lift cylinders not in phase:

fully extend cylinders

and hold hydraulic lever until all cylinders are fully
extended.

Cylinders not installed in proper series:

Wing

cylinders are smaller diameter than center cylinders.
Reinstall cylinders properly.

Hoses not properly connected:

check hose routing

HYDRAULIC - ENTIRE UNIT SETTLING

Depth stop valve not working:

repair valve

HYDRAULIC - UNIT SETTLING, ONE WING
RAISING

Center frame cylinder leaking internally on side
of unit that wing is raising:

repair center master

cylinder.

HYDRAULIC - WING SETTLING

Wing cylinder leaking:

repair cylinder.

COULTER GANG PLUGGING

Operating depth too deep:

raise unit or raise

coulters.

Conditions too wet

: wait until conditions more

favorable.

COULTER GANG WILL NOT TURN OR
PUSHES SOIL

Depth set too deep for loose or wet conditions:

raise implement, raise coulters, or wait until
conditions are more favorable.

Gang bearing failure:

replace bearing

COULTER BLADES LOOSE AND/OR
SHEARING ROLL PIN

Gang not tightened properly:

retighten gang shafts

to 1250-1500 ft-lbs. If gangs have ran loose, gangs
may require disassembly to remove soil to properly
torque gang shafts. Replace any worn components,
shafts/spools, etc.

5-2

Содержание 2130




















































































Результаты поиска

Содержание 2130

Отзывы:

Похожие инструкции для 2130

Бренды по названию

Популярные бренды

Landoll 2130, Руководство оператора

Результаты поиска

Содержание 2130

Отзывы:

Похожие инструкции для 2130

Бренды по названию

Популярные бренды