background image

PAGE 2

•  

WARNING!  

THE GRILL IS FOR OUTDOOR USE ONLY!

•  

WARNING!

   NEVER USE GASOLINE,  GASOLINE-TYPE

     FUEL, KEROSENE,  CHARCOAL LIGHTER FLUID, OR
     SIMILAR LIQUIDS TO START OR "FRESHEN UP" A FIRE
     IN THIS APPLIANCE.   KEEP ALL SUCH LIQUIDS AWAY
     FROM THE  APPLIANCE WHEN IN USE.

•   DO NOT STORE  FLAMMABLE LIQUIDS OR MATERIALS

     ON THE BOTTOM SHELF OR SIDE SHELF.

•   THE GRILL IS FOR ADULT USE ONLY.

•   

WARNING!

   THIS GRILL GETS  EXTREMELY HOT DURING

     USE!   USE EXTREME CAUTION AROUND THE GRILL.

•   USE CAUTION WHEN OPENING THE LID AS HOT STEAM

     OR A FLARE UP COULD CAUSE BURNS.

•   KEEP THE GRILL A MINIMUM OF 24 IN. AWAY FROM

     BUILDINGS, STRUCTURES, ANY FLAMMABLE ITEMS
     AND VEHICLES DURING USE.

•   KEEP CHILDREN AND PETS AWAY WHILE THE GRILL IS

     BEING USED.

•   USE CAUTION AFTER THE FIRE HAS BEEN

      EXTINGUISHED- SURFACES WILL REMAIN HOT FOR
     SOME TIME.

•  

WARNING!  

NEVER PUT YOUR FINGERS IN THE AUGER

     CHANNEL FOR ANY REASON!

•   THE HOPPER PELLET FUEL SCREEN MUST BE IN PLACE

     DURING USE.

•   NEVER USE THE GRILL UNDER COVERED PORCHES,

     AWNINGS,  COMBUSTIBLE CEILINGS, LOW HANGING
     TREE BRANCHES, TRELLIS, OR OVERHANGS OF ANY
     KIND.

•   NEVER USE INSIDE ENCLOSED AREAS SUCH PATIOS,

    GARAGES, ENCLOSED ROOMS,  BUILDINGS OR TENTS.

•   DO NOT USE IN WINDY  CONDITIONS.
•   DO NOT USE IN VERY WET OR RAINY CONDITIONS.

•   KEEP THE LID CLOSED DURING USE.   THIS PELLET GRILL

     IS INTENDED TO BE USED WITH A CLOSED LID.

•   NEVER USE THIS GRILL AS A HEATER.
•   THIS GRILL IS NOT FOR COMMERCIAL USE.
•   BEFORE STARTING, MAKE SURE THE GREASE BUCKET IS

     IN PLACE.

•   ALWAYS UNPLUG GRILL AFTER USING.   WIND CORD 

     AROUND THE CORD WRAP SO IT IS OUT OF THE WAY.

•   DURING USE, THE PLUG WIRING SHOULD BE SORTED

     SO IT DOES NOT IMPOSE A TRIPPING HAZARD.

•   ALWAYS USE THE GRILL ON A HARD, STABLE AND

     LEVEL SURFACE.

•   THIS GRILL OPERATES  AUTOMATICALLY THROUGH THE

     CONTROL PANEL.   DO NOT MANUALLY FILL THE FIRE
     POT OR OVER-FILL THE FIRE POT BY HAND.   THIS WILL
     CAUSE A  DANGEROUS OVER-FIRING  CONDITION.

READ FIRST!   RULES FOR PELLET KETTLE GRILL SAFE OPERATION.

®

•   THE SIDE SHELF CAN HOLD 15 LBS. SAFELY, DO NOT

     PUT MORE THAN 15 LBS. ON THE SIDE SHELF.

•   DO NOT LEAN OR PUSH DOWN ON THE SIDE SHELF.
•   DO NOT MOVE THE GRILL WHILE IT IS BEING USED.
•   DO NOT USE  ACCESSORIES NOT SPECIFIED FOR USE

     WITH THIS APPLIANCE.

•   MAKE SURE THE FRONT WHEEL CASTERS ARE

     LOCKED WHILE IN USE.

•   DO NOT LEAVE  UNATTENDED AT ANY TIME WHILE

     IN USE.

•   BEFORE EACH USE, MAKE SURE THE GRILL IS IN

     GOOD WORKING CONDITION.

•   DO NOT ALTER THE GRILL IN ANY WAY.
•   DO NOT MODIFY OR HARDWIRE THE AUGER TO 

     RUN  CONTINUOUSLY.

•   DO NOT USE THE GRILL UNTIL IT IS  COMPLETELY

     ASSEMBLED WITH ALL PARTS SECURELY
     TIGHTENED.

•   THE GRILL MUST BE  COMPLETELY COOLED OFF

     AND MUST BE  EXTINGUISHED BEFORE ANY COVER
     CAN BE USED.

•    MAINTAINING THE GRILL IS THE  RESPONSIBILITY OF

     THE OWNER OR USER.   THE FIREBOWL, DRIP TRAY
     AND DRIP TRAY TUBE MUST BE CLEANED
      OCCASIONALLY TO REMOVE GREASE BUILDUP.
     FAILURE TO CLEAN GREASE BUILDUP CAN CAUSE
     GREASE FIRES WHICH ARE VERY  DANGEROUS.

•  

WARNING!

   AFTER EVERY 20 HRS OF USE, THE FIRE

     POT MUST BE CLEANED OUT TO REMOVE ANY
     ASH BUILDUP.   THIS IS REQUIRED  MAINTENANCE.

•   NEVER POUR WATER INTO THE FIREBOWL, FIRE POT

     OR DRIP TRAY.

•   IF A GREASE FIRE WERE TO OCCUR, BAKING SODA

     CAN BE USED TO EXTINGUISH THE FIRE.   USE
     EXTREME CAUTION NOT TO BURN YOURSELF.

•   IF THE FIRE DOES NOT EXTINGUISH, REMOVE THE 

     FOOD IF POSSIBLE.   KEEP THE LID CLOSED, CLOSE
     THE CHIMNEY DAMPER AND PRESS THE POWER 
     BUTTON TO OFF.

•   ONCE THE FIRE IS  EXTINGUISHED, CLEAN THE

     GREASE BUILDUP BEFORE COOKING IS RESUMED.

•   DISPOSAL OF ASHES - ANY ASHES THAT ARE 

     REMOVED FROM THE GRILL SHOULD BE PLACED IN
     A METAL CONTAINER WITH A TIGHT FITTING LID.
     THE CLOSED CONTAINER OF ASHES SHOULD BE
     PLACED ON A  NONCOMBUSTIBLE FLOOR OR 
     GROUND, WELL AWAY FROM ALL  COMBUSTIBLE
     MATERIALS, PENDING FINAL DISPOSAL.   IF THE 
     ASHES ARE DISPOSED OF BY BURIAL IN SOIL OR
     OTHERWISE LOCALLY DISPERSED, THEY SHOULD BE
     RETAINED IN THE CLOSED CONTAINER UNTIL ALL
     CINDERS HAVE  THOROUGHLY COOLED.

Содержание 470106

































Отзывы: