Landia POP-I страница 31 Скачать руководство пользователя | Manualshive

Страница: 31 / 127

background image

CA01A.C01

Service instructions, mixer type POP-I

Page 1/8

Landia Inc.

Issued on: 01 March 1997

Cary, NC 27513

Rev. date: 24. October 2018

Executed by: AJ/BNV

Accepted by: SL/KT

INTRODUCTION

The type POP-I is a horizontal submersible mixer.

During operation the mixer is locked by a conic stop console or stop bracket fixed to the guide pipe to obtain
stability.
The mixing takes place by means of an electric motor coupled to the propeller by means of a planetary gear.

The oil filled coupling/oil chamber between motor and gear is in an open connection with the gear, so the oil
cools and lubricates the gear and the mechanical shaft seal between the oil chamber and the motor.

The hub is mounted on the propeller shaft, the output shaft of the gear.
The exterior sealing system consists of three sealing rings with grease filled chambers between these.

The following pages describe the connection and the maintenance of mixers type POP-I.

Application:

This mixer is to be used for flow creation, mixing and homogenization of liquids with a high or low dry matter
content, like e.g. wastewater, sludge and paper pulp, as well as chemical liquids and manure. The mixer can be
placed in square and circular tanks and is to be applied only fully submerged below liquid level.
If the mixer is to be applied for other purposes, contact Landia for advice.

WARNING - PLEASE NOTE THE FOLLOWING POINTS!

IMPORTANT!



Only a certified electrician is allowed to connect the unit.

IMPORTANT!



Prior to installation and start up, check that the equipment is mounted
correctly to the mixer, as well as the equipment in the tank.

IMPORTANT!



Prior to the first start of the mixer, the propeller shaft must be rotated
manually. . This also applies if the mixer has not been in operation for a
longer period.

IMPORTANT!



The electrical cable is always to be secured by means of the chain to
prevent the cable from getting into contact with the propeller. If the mixer
is not supplied with a chain, the cable is to be protected against damage in
another way, e.g. by means of a cable mesh.

IMPORTANT!



It must be verified that the propeller cannot touch the tank under any
circumstances.

IMPORTANT!



The mixer must be fully below liquid level during operation.

IMPORTANT!



Prior to hoisting the mixer for service/repair

IT IS IMPERATIVE

that

the electrical connection of the mixer is switched off or locked out. Prior
to service/repair the mixer should be cleaned thoroughly.

«
...
29
30
31
32
33
...
»

Содержание POP-I
































































































































Отзывы:

Нет отзывов

Похожие инструкции для POP-I

Бренд: TL Audio Страницы: 21

Бренд: TerraTec Страницы: 10

Бренд: DAPAudio Страницы: 16

Бренд: Mackie Страницы: 36

Бренд: Electrolux Страницы: 12

Бренд: Electrolux Страницы: 4

Бренд: Electrolux Страницы: 2

Бренд: Electrolux Страницы: 76

Бренд: Electrolux Страницы: 2

ST. LOUIS MINIMIX

Бренд: Cimo Страницы: 10

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 46

Бренд: Rolls Страницы: 1

Бренд: Rolls Страницы: 4

Бренд: PFT Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды