background image

Landa SLT/SLX   •  Gas 8.914-002.0  •  Rev. 4/13

15

 

 PRESSURE 

W

ASHER  

OPERA

TOR’S MANU

AL

  

MAINTENANCE & SERVICE

For additional burner component information, see  
Burner Assembly Exploded View page. It is recom-
mended that the oil burner be serviced yearly or as 
needed. Contact your local service center

.

Beckett Burner Air Adjustment:

Air Shutter 

Locking Screw

Air Shutter 

Locking Screw

Air Band Locking 

Screw

Air Shutter

Air Band

To adjust

, start the machine and turn burner ON. 

Loosen two locking screws found in the air shutter 
openings (see illustration) and close air shutter until 
black smoke appears from burner exhaust vent. Note 
air band position. Next, slowly open the air shutter 
until white smoke just starts to appear. Turn air shutter 
halfway back to the black smoke position previously 
noted. Tighten locking screws.
If the desired position cannot be obtained using only 
the air shutter, lock the air shutter in as close a position 
as can be obtained, then repeat the above procedure 
on the air band setting.

LANDA Surefire Burner Air Adjustment:

Reference Numbers

Air Band Locking Screws

Air Band

To adjust, start machine and turn burner ON. Loosen 
two locking screws found on the air band and close air 
band until black smoke appears from burner exhaust 
vent. Note air band position. Next, slowly open the air 
band until white smoke just starts to appear. Turn air 
band halfway back to the previously noted position. 
Tighten locking screws.

Coil Removal

Coil removal,  because of freeze breakage or to clean 
soot from it, can be done quickly and easily.
   1. Disconnect hose from pump to inlet side of the 

coil.

   2.  Carefully disconnect the thermostat sensor making 

sure you do not crimp the capillary tube.

   3. Remove burner assembly from combustion  

chamber.

   4.  Remove the 3-3/8" bolts from each side of coil and 

tank assembly (these bolts are used to fasten tank 
to chassis).

   5.  Remove fittings connected to the 1/2" pipe nipples 

from inlet and discharge sides of coil.

   6.  Remove top tank wrap, bend back insulation tabs 

and fold back blanket.

   7. R e m ove   b o l t s   t h a t   h o l d   d ow n   c o i l   t o  

bottom wrap.

   8.  Remove coil.
   9.  Replace or repair the coil and any insulation found 

to be broken or torn.

 10.  Remove insulation retainer plates.

Coil Reinstallation

Reinstall new or cleaned coil reversing Steps 9  
through 1.

Содержание SLT5-30224E 1.110-518.0





















































Отзывы: