manualshive.com logo in svg
background image

12

Operations

Detergents & General Cleaning 
Techniques

WARNING: Some detergents may 
be harmful if inhaled or ingested, 
causing severe nausea, fainting 
or poisoning. The harmful 
elements may cause property 
damage or severe injury.

STEP 1:

 Use detergent designed 

specifically for pressure washers. 
Household detergents could 
damage the pump. Prepare 
detergent solution as required by 
the manufacturer. Fill a container 
with pressure washer detergent. 
Place the filter end of detergent 
suction tube into the detergent 
container.

STEP 2:

Turn variable pressure control valve on the 

wand counter clockwise for low pressure until you 
observe detergent flowing through the detergent pick-
up tube

STEP 3:

 With the engine running, 

pull trigger to operate machine. 
Liquid detergent is drawn into the 
machine and mixed with water. 
Apply detergent to work area. Do 
not allow detergent to dry on 
surface.

IMPORTANT: You must flush the detergent 
injection system after each use by placing the 
suction tube into a bucket of clean water, then run 
the pressure washer with detergent valve open for 
1-2 minutes.

Thermal Pump Protection

If you run your pressure washer for 3-5 minutes without 
pressing the trigger on the spray gun, circulating water 
in the pump can reach high temperatures. When the 

water reaches this temperature, the pump protector 
engages and cools the pump by discharging the warm 
water onto the ground. This thermal device prevents 
internal damage to the pump.

Cleaning Tips

Pre-rinse cleaning surface with fresh water. Place 
detergent suction tube directly into cleaning solution 
and apply to surface at low pressure (for best results, 
limit your work area to sections approximately 6 feet 
square and always apply detergent from bottom to top). 
Allow detergent to remain on surface 1-3 minutes. Do 
not allow detergent to dry on surface. If surface 
appears to be drying, simply wet down surface with 
fresh water. If needed, use brush to remove stubborn 
dirt. Rinse at high pressure from top to bottom in an 
even sweeping motion keeping the spray nozzle 
approximately 1 foot from cleaning surface. Use over-
lapping strokes as you clean and rinse any surface. For 
best surface cleaning action spray at a slight angle.

Recommendations:

Before cleaning any surface, an inconspicuous 
area should be cleaned to test spray pattern 
and distance for maximum cleaning results.

If painted surfaces are peeling or chipping, use 
extreme caution as pressure washer may 
remove the loose paint from the surface.

Keep the spray nozzle a safe distance from the  
surface you plan to clean. High pressure wash 
a small area, then check the surface for 
damage. If no damage is found, continue to 
pressure washing.

       

CAUTION - Never use:

Bleach, chlorine products and other corrosive 
chemicals

Liquids containing solvents (i.e., paint thinner, 
gasoline, oils)

Tri-sodium phosphate products

Ammonia products

Acid-based products

These chemicals will harm the machine and will 
damage the surface being cleaned.

Rinsing

It will take a few seconds for the detergent to clear. 
Apply safety latch to spray gun.Select and install the 
desired high pressure nozzle. 

CAUTION: Remove of the pick up tube from 
detergent bucket will draw air into pump causing 
cavitation and low pressure.

Landa PGHW Operator’s Manual   8.916-485.0 - Y

WARNING

Detergent Injector

Содержание PGHW series



















































Отзывы: