manualshive.com logo in svg

Landa 1.109-078.0, Руководство оператора, Страница: 22 / 26

Поделиться
Скачать
Landa 1.109-078.0 Скачать руководство пользователя страница 22

22

Maintenance

PROBLEM

POSSIBLE CAUSE

SOLUTION

WATER 

TEMPERATURE 

TOO HOT

Incoming water to machine warm or 
hot

Lower incoming water temperature.

Fuel pump pressure too high

Readjust fuel pressure.

Fuel pump defective

Replace fuel pump.

Detergent line sucking air

Tighten all clamps. Check detergent line for holes.

Defective high limit switch

Replace.

Incorrect fuel nozzle size

See exploded view parts list for proper size.

Insufficient water supplied

Check GPM to machine.

Restricted water flow

Check nozzle for obstruction and proper size.

PUMP MOTOR 

STOPS AFTER A 

FEW MINUTES OF 

OPERATION OR 

STARTS SLOW

Insufficient voltage

Use heavier drop cord and check voltage at recep-
tacle. Check name plate for amperage draw.

Plugged nozzle

Remove and clean nozzle. Turn on water pump and 
flush lines, replace nozzle.

Wrong spray nozzle

See serial plate for minimum nozzle size.

Automatic overload switch tripped

Allow motor to cool - switch will automatically reset.

Motor wet

Allow to dry.

Short in electrical wiring

Wire contacts should be clean and tight. No breaks in 
wires.

Coil liming up causing excessive 
pressure

See section on Preventative Maintenance.

Water pump low or out of oil causing 
the pump to bind up

Fill to correct level.

RELIEF VALVE 

LEAKS OR 

SPRAYS OUT 

WATER

Spray nozzle plugged

Remove nozzle and clean out obstruction.

Mis-adjusted or defective relief valve Adjust or replace as needed.

Scale or dirt plugging inside of coils

See "Preventative Maintenance Cleaning of Coils."

DETERGENT NOT 

DRAWING

Air leak

Tighten all clamps. Check detergent lines for holes.

Detergent metering valve packing 
not tight or packing worn

Tighten nut. Replace valve or packing.

Filter screen on detergent suction 
hose plugged

Clean or replace.

Dried up detergent plugging metering 
valve or injector

Clean and flush.

Restrictor in float tank missing

Install restrictor.

High viscosity of detergent

Dilute detergent to specifications. Read detergent 
label.

Landa PHW Operator’s Manual   8.917-417.0 - D

Содержание 1.109-078.0



























Отзывы:

Нет отзывов