background image

30

Section 6: Maintenance & Lubrication

SB1051, SB1064, SB1574, & SB2584 with S/N 881640- Snow Blowers   370-027M

2/11/21

Table of Contents

Chute Bearings

Refer to Figure 6-3 on page 29:

Over time, the chute bearings (#1) can develop some 

wear making it hard to rotate chute (#3). If they do wear, 

loosen bolts (#2) and rotate chute bearings (#1) to a new 

wear surface. Retighten bolts (#2) to the correct torque 

before putting Snow Blower back into service.

Roller Chain Take-up Replacement

Figure 6-5

Drive Chain

Refer to Figure 6-5:

1. Loosen hand knobs (#9) and remove rear drive shaft 

guard (#1).

2. Remove cap screws (#4) and idler guard (#2). Keep 

guard and guard hardware for reattachment.

3. Loosen cap screw (#3) and pull up on take-up 

sprocket (#8). Remove drive chain. 

4. Inspect drive chain for wear or have your nearest 

Land Pride service center inspect the drive chain. A 

worn drive chain will accelerate sprocket wear. 

Replace worn drive chain when needed.

5. Install existing or new drive chain as needed. Pull up 

on take-up sprocket (#8) and position top chain 

strand of drive chain under the take-up sprocket.

6. Push down on take-up sprocket until vertical 

movement in the middle of bottom chain strand has 

3/8" to 1/2" slack.

7. Hold sprocket in this position and tighten 5/8"-11 cap 

screw (#3) to the correct torque.

33288

Drive Chain Part Number

Part No.

Part Description

809-301C

#60 ROLLER CHAIN x 84 PITCHES 

WITH CONNECTOR

IMPORTANT: 

Do not over tension drive chain. A 

tight drive chain will overload drive shaft, auger shaft 

and bearings. Damage to components due to an 

over tensioned drive chain will void its warranty.

8. Attach idler guard (#2) with 5/16"-18 x 1" GR5 hex 

head cap screws (#4), flat washers (#7), spring lock 

washers (#6), and hex nuts (#5). Tighten hex nuts to 

the correct torque.

9. Replace rear drive shaft guard (#1) and secure with 

hand knobs (#9). Hand tighten knobs.

Inner Skid Shoe Replacement

Figure 6-6

Inner Skid Shoes (Optional)

Refer to Figure 6-6:

Inspect inner skid shoes for wear and replace as needed.
1. Place support blocks under Snow Blower support 

rests (#7) to hold unit off the ground high enough to 

remove skid shoes (#1) from skid shoe mounts (#2). 

2. Lower Snow Blower onto the support blocks, place 

gear selector in park or in neutral with park brake set, 

shut engine off, remove switch key, and wait for PTO 

to stop running before dismounting tractor.

3. Install right side inner skid shoe as follows:

a. Remove pin (#4), top spacers (#3, #5, and/or #6), 

and used skid shoe (#1). Save spacers for 

reinstallation in step 3d below.

b. Remove spacers (#3, #5, and/or #6) from used 

skid shoe (#1). Reinstall these spacers on the 

new skid shoe.

c. Insert new skid shoe (#1) in skid shoe mount (#2). 
d. Install spaces removed in step 3a above onto new 

skid shoes (#1).

e. Secure spacers and skid shoes with existing wire 

retaining pin (#4). Make sure wire retainer is 

caught over end of pin.

4. Repeat step 3 above to install left side skid shoe.

33286

Inner Skid Shoe Part Numbers

Part No.

Part Description

301-293H

BUTTON TYPE SKID SHOE

Содержание SB10 Series











































Отзывы: