Land Pride SB10 Series Скачать руководство пользователя

Страница: 32 / 42

Section 6: Maintenance & Lubrication

SB1051, SB1064, SB1574, & SB2584 with S/N 881640- Snow Blowers 370-027M

2/11/21

Table of Contents

Chute Bearings

Refer to Figure 6-3 on page 29:

Over time, the chute bearings (#1) can develop some

wear making it hard to rotate chute (#3). If they do wear,

loosen bolts (#2) and rotate chute bearings (#1) to a new

wear surface. Retighten bolts (#2) to the correct torque

before putting Snow Blower back into service.

Roller Chain Take-up Replacement

Figure 6-5

Drive Chain

Refer to Figure 6-5:

1. Loosen hand knobs (#9) and remove rear drive shaft

guard (#1).

2. Remove cap screws (#4) and idler guard (#2). Keep

guard and guard hardware for reattachment.

3. Loosen cap screw (#3) and pull up on take-up

sprocket (#8). Remove drive chain.

4. Inspect drive chain for wear or have your nearest

Land Pride service center inspect the drive chain. A

worn drive chain will accelerate sprocket wear.

Replace worn drive chain when needed.

5. Install existing or new drive chain as needed. Pull up

on take-up sprocket (#8) and position top chain

strand of drive chain under the take-up sprocket.

6. Push down on take-up sprocket until vertical

movement in the middle of bottom chain strand has

3/8" to 1/2" slack.

7. Hold sprocket in this position and tighten 5/8"-11 cap

screw (#3) to the correct torque.

33288

Drive Chain Part Number

Part No.

Part Description

809-301C

#60 ROLLER CHAIN x 84 PITCHES

WITH CONNECTOR

IMPORTANT:

Do not over tension drive chain. A

tight drive chain will overload drive shaft, auger shaft

and bearings. Damage to components due to an

over tensioned drive chain will void its warranty.

8. Attach idler guard (#2) with 5/16"-18 x 1" GR5 hex

head cap screws (#4), flat washers (#7), spring lock

washers (#6), and hex nuts (#5). Tighten hex nuts to

the correct torque.

9. Replace rear drive shaft guard (#1) and secure with

hand knobs (#9). Hand tighten knobs.

Inner Skid Shoe Replacement

Figure 6-6

Inner Skid Shoes (Optional)

Refer to Figure 6-6:

Inspect inner skid shoes for wear and replace as needed.
1. Place support blocks under Snow Blower support

rests (#7) to hold unit off the ground high enough to

remove skid shoes (#1) from skid shoe mounts (#2).

2. Lower Snow Blower onto the support blocks, place

gear selector in park or in neutral with park brake set,

shut engine off, remove switch key, and wait for PTO

to stop running before dismounting tractor.

3. Install right side inner skid shoe as follows:

a. Remove pin (#4), top spacers (#3, #5, and/or #6),

and used skid shoe (#1). Save spacers for

reinstallation in step 3d below.

b. Remove spacers (#3, #5, and/or #6) from used

skid shoe (#1). Reinstall these spacers on the

new skid shoe.

c. Insert new skid shoe (#1) in skid shoe mount (#2).
d. Install spaces removed in step 3a above onto new

skid shoes (#1).

e. Secure spacers and skid shoes with existing wire

retaining pin (#4). Make sure wire retainer is

caught over end of pin.

4. Repeat step 3 above to install left side skid shoe.

33286

Inner Skid Shoe Part Numbers

Part No.

Part Description

301-293H

BUTTON TYPE SKID SHOE

Содержание SB10 Series











































Результаты поиска

Содержание SB10 Series

Отзывы:

Похожие инструкции для SB10 Series

Бренды по названию

Популярные бренды

Land Pride SB10 Series, Руководство оператора

Результаты поиска

Содержание SB10 Series

Отзывы:

Похожие инструкции для SB10 Series

Бренды по названию

Популярные бренды