Land Pride SA20 Series, Руководство оператора

Страница: 17 / 38

Section 1: Assembly & Set-up
Table of Contents
SA20 Hydraulic Post Hole Diggers 317-215M 3/8/18
13
Hook-Up Post Hole Digger
DANGER
!
To prevent serious injury or death:
A crushing hazard exists while hooking-up and unhooking
attachment. Do not allow anyone to stand between attachment
and power machine while approaching or backing away from
the attachment. Do not operate lift and/or tilt controls while
someone is near the power machine and/or attachment.
WARNING
!
To prevent serious injury or death:
Make sure skid/loader plate is properly attached to the Post
Hole Digger. The skid/loader plate must be secured under the
auger hitch top angle bar. Lock pins must extend fully through
bottom slots in the auger hitch in the locked down position. An
improperly attached hitch can allow equipment to fall and/or
be thrown towards bystanders and/or operator.
Hook-Up Post Hole Digger Hitch Plate
Refer to Figure 1-11:
1. Check for and remove all debris in hitch point areas
of skid/loader plate and auger hitch.
2. Raise lock pins on skid/loader plate.
3. Drive skid steer/tractor slowly to Post Hole Digger
making sure skid/loader plate is parallel with auger
hitch top angle bar.
4. Rotate top of skid steer/tractor tilt arms slightly
forward.
5. Position top of skid/loader plate under the auger hitch
top angle bar and slowly raise loader arms until skid/
loader plate is seated under the top angle bar.
6. Rotate top of skid steer loader arms back until skid/
loader plate makes full contact with auger hitch.
7. Lower lock pins on skid/loader plate. Make sure lock
pins go through bottom slots in auger hitch and are in
the locked down position.
Hook-Up Hydraulic Hoses to Tractor
DANGER
!
To prevent serious injury or death:
Hydraulic fluid under high pressure will penetrate the skin
and/or eyes causing a serious injury. Wear protective gloves
and safety glasses or goggles when working with hydraulic
systems. Use a piece of cardboard or wood rather than hands
when searching for leaks. A doctor familiar with this type of
injury must treat the injury within a few hours or gangrene
may result. DO NOT DELAY.
WARNING
!
To prevent serious injury or death:
Make sure hydraulic hoses are properly routed so that they
will not become pinched or kinked while operating equipment.
A pinched or kinked hose can burst and leak hydraulic fluid.
Hook-Up Auger Hitch to Tractor/Skid Steer
Figure 1-11
Hook-Up Hydraulic Hoses to Tractor
Figure 1-12
Refer to Figure 1-12:
1. Connect quick release couplers (#1A & #2A) to the
tractor’s high pressure outlets.
2. While seated in the tractor seat, lift Post Hole Digger
up until auger is off the ground 1 to 2 inches.
3. With tractor set at an idle, engage hydraulics to view
auger rotation. Auger should rotate clockwise when
looking down from above. If auger rotates
counterclockwise, switch couplers at the duplex out:
a. Shut power machine down using “Power Machine
Shutdown Procedure” on page 7 before
dismounting.
b. Switch quick release couplers (#1A & #2A) at the
duplex outlet on the tractor.
4. Return to the tractor and repeat steps 1-3 to verify
auger is rotating properly.
5. Secure hydraulic hoses (#1 & #2) with customer
supplied ties along tractor loader arm to keep hoses
from becoming pinched, stretched, and/or kinked.
6. Cycle loader through complete range of motions to
verify hydraulic lines will not be pinched, stretched,
and/or kinked. Make any necessary adjustments.
37273
37281
NOTE: Customer to select and supply ties for
securing hydraulic hoses along tractor loader arm.
Land Pride recommends ties that can be reused
without cutting them.