Land Pride RCR16 Series Скачать руководство пользователя страница 3

1

Important Safety Information

12/14/01

RCR16 Series Rotary Cutters   312-742M

Land Pride

Important Safety Information

Keep Riders
Off Machinery

Riders obstruct the operator’s

view they could be struck by
foreign objects or thrown from the
machine.

Never allow children to operate

equipment.

!

Be Aware of Signal Words

A signal word designates a degree or
level of hazard seriousness. The
signal words are:

Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury. This
signal word is limited to the most
extreme situations, typically for
machine components that, for
functional purposes, cannot be
guarded.

Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury, and
includes hazards that are exposed
when guards are removed. It may
also be used to alert against unsafe
practices.

Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury. It
may also be used to alert against
unsafe practices.

For Your Protection

Thoroughly read and understand

the “Safety Label” section, read all
instructions noted on them.

!

DANGER

!

WARNING

!

CAUTION

Shutdown and Storage

Lower machine to ground, put

tractor in park, turn off engine,
and remove the key.

Detach and store implements in a

area where children normally do
not play. Secure implement by
using blocks and supports.

OFF

ON

These are common practices that may or may not be applicable to the products described in
this manual.

Содержание RCR16 Series





























Отзывы: