Land Pride RCP2560 Series страница 21 Скачать руководство пользователя | Manualshive

Страница: 21 / 38

background image

19

Section 3: Hydraulics

4/28/08

RCP2560 & RCPM2560 Series Parallel Arm Rotary Cutter 316-057M

Land Pride

Table of Contents

The hydraulic pump/motor circuit is shown in
Figure 3-3. It operates via a tractor driven PTO and is
not connected to tractor hydraulics. The pump receives

fluid from a 35 gallon reservoir. If the cutter blades are
stalled, an overpressure relief valve opens to provide a
return path to the reservoir.

Marking Hydraulic Line Lengths

Hydraulic lines are marked to length from motor to
pump and pump to motor as outlined in Figure 3-4
below.

Tie Strap

Return Line

Pressure Line

**Twist return hose (811-404C) counter-
clockwise until it follows the same
contour as pressure hose
(811-403C).

Pressure Line

Outer End

Hose Locations for Hydraulic

Pump and Motor

Figure 3-4

*Orient 811-411C
Hyd. Fittings so they
are 45˚ down
towards deck

13776

Hydraulic Pump Motor Circuit

Figure 3-3

12262

«
...
19
20
21
22
23
...
»

Содержание RCP2560 Series







































Отзывы:

Нет отзывов

Похожие инструкции для RCP2560 Series

Бренд: Echo Страницы: 9

Ecocutter ECC-125

Бренд: Alpha Professional Tools Страницы: 36

Бренд: Tanaka Страницы: 20

Бренд: Zenoah Страницы: 24

Бренд: KEENCUT Страницы: 8

Бренд: Laski Страницы: 37

EMS 350-SL COMPACT

Бренд: Würth Страницы: 152

Бренд: Rubi Страницы: 12

Бренд: Presto Страницы: 5

Бренд: Logan Страницы: 4

Бренд: Dolmar Страницы: 80

K 650/700 Active

Бренд: Partner Страницы: 96

Бренд: CanyCom Страницы: 94

Бренд: CanyCom Страницы: 93

Бренд: CanyCom Страницы: 98

Бренд: Hiace Страницы: 12

Бренд: CAB Страницы: 22

Бренд: Stihl Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды