Land Pride RCM3712 Скачать руководство пользователя | Manualshive

Страница: 18 / 64

background image

Section 1: Assembly & Set-up

RC(M)3712 & RCG(M)3712 Rotary Cutters 334-203M

11/6/18

14

Table of Contents

Fixed Clevis Hitch Hook-up

DANGER

!

To avoid serious injury or death: A crushing hazard exists

while hooking-up and unhooking implement. Keep people and

animals away while backing-up to implement or pulling away

from implement. Do not operate hydraulic controls while a

person or animal is directly behind the power machine or near

the implement.

WARNING

!

To avoid serious injury or death: The ball detent pin must be

fully inserted into the park jack with ball visible and popped

out on the far side of the jack before working on or around an

unhooked cutter.

Refer to Refer to Figure 1-9:

1.

Make certain park jack (#3) is properly attached
to the cutter hitch and secured with detent pin (#8). If
park jack is not vertical, refer to

“Park Jack Angle

Alignment”

2. Store center 3-point link in its storage hook.

3. Start tractor and raise 3-point arms fully up.

4. Carefully back tractor within close proximity of

clevis (#9).

5. Shut tractor down properly before dismounting. Refer

to

“Tractor Shutdown Procedure”

6. Verify tractor drawbar is adjusted correctly. Refer to

“Drawbar Set-up”

dimensions on page 11.

7.

Raise or lower park jack (#3) to align clevis (#9) with
tractor drawbar. Drawbar should fit between lower
and upper plates of clevis.

8. Restart tractor and continue to back tractor up to

cutter hitch until hitch holes in tractor drawbar and
hitch clevis (#9) are aligned.

9. Shut tractor down properly before dismounting.

10. Attach cutter to tractor drawbar with customer

supplied hitch pin (#1) and hairpin cotter (#2).

11. Lower park jack (#3) until hitch weight is supported

by drawbar.

12. Remove park jack (#3) from hitch and attach it to the

left-hand wing storage base with detent pin (#8).
Make sure base is level with or lower than the head
especially after the wings are folded up. See cover
picture for correct positioning.

13. Attach hitch safety chain (#4) to tractor. Adjust chain

length to remove all slack except what is necessary
to permit turning. Lock chain hook securely to the
safety chain.

14. Continue with

“Hydraulic Hook-up”

NOTE:

Bolt (#10) and spacer (#11) may be

removed to increase hitch flexibility. If removed, an
equal number of flat washers (#12) should be added
above and below the drawbar to minimize the gap
and reduce ware. Flat washers (#12) are customer
supplied.

NOTE:

Hitch pin (#1) and hairpin cotter (#2) are

supplied by customer.

IMPORTANT:

Protect park jack by storing it on the

left wing deck before moving the cutter. Make sure
jack is stored with its base level or lower than the
head to prevent water and freeze damage.

Fixed Clevis Hitch Hook-up

Figure 1-9

37298

70457

«
...
16
17
18
19
20
...
»

Содержание RCM3712

































































Отзывы:

Нет отзывов

Похожие инструкции для RCM3712

Evolution3 SmartFold

Бренд: KEENCUT Страницы: 48

Бренд: KEENCUT Страницы: 29

Бренд: Zenoah Страницы: 4

Бренд: Huskie Tools Страницы: 12

Бренд: Craftsman Страницы: 26

Бренд: Craftsman Страницы: 26

Бренд: Craftsman Страницы: 23

Бренд: Craftsman Страницы: 18

Бренд: Craftsman Страницы: 37

Бренд: Craftsman Страницы: 47

Бренд: Craftsman Страницы: 52

Бренд: Raider Страницы: 96

Бренд: QEP Страницы: 8

AT-3623 AT-3630

Бренд: Dolmar Страницы: 116

Бренд: Ryobi Страницы: 28

Classen HSC18HD

Бренд: Schiller Страницы: 47

Бренд: Talet Equipment Страницы: 20

Бренд: Zenoah Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды