Land Pride RCF3696 Скачать руководство пользователя страница 64

Страница: 64 / 76

Section 5: Maintenance & Lubrication

RCF3696, RCFM3696, RCF3610, & RCFM3610 Rotary Cutters 326-600M

Table of Contents

8/20/21

Flex Couplers

Figure 5-7

Flex Couplers

Refer to Figure 5-7:

Replace two rubber discs (#1), (Land Pride Part No.

1785273), as follows: If additional repair parts are

required, refer to Land Pride’s Parts Manuals 326-600P

for RCF(M)3696 and 326-423P for RCF(M)3610 cutters.
1. Insert three bolts (#3) through the holes in flange

weldment (#7).

2. Place beaded washers (#2) over the three bolts with

bead facing rubber disc (#1).

3. Place bushings (#6), rubber disc (#1), washers (#5),

2nd rubber disc (#1), 2nd bushing (#6) and 2nd

washer (5) over the three bolts as shown.

4. Secure with nuts (#4). Do not tighten.
5. Insert three bolts (#3) through holes in flanged

hub (#8).

6. Repeat steps 2 through 4.
7.

Tighten nuts (#4) evenly with nuts torqued

35 to 40 ft-lb. Beaded washers (#2) should be

embedded halfway into the rubber disc.

14560

Skid Shoe Replacement

Figure 5-8

Skid Shoe Maintenance

Refer to Figure 5-8:

WARNING

To avoid serious injury or death:
Excessive wear on skid shoes can damage side panels, cause

inadequate operation of cutter, and create a safety hazard.

Always replace skid shoes at the first sign of wearing thin.

A skid shoe is mounted to each side of the cutter. Check

both skid shoes for wear and replace if needed. Order

only genuine Land Pride parts from your local Land Pride

dealer.
1. Remove 3/8" hex whiz nuts (#3), 3/8" plow bolts (#2)

and skid shoe (#1) as shown.

2. Plow bolts should be checked for wear and replaced

if necessary.

3. Attach new skid shoe (#1) to cutter with existing

3/8" plow bolts (#2) and secure with 3/8" hex whiz

nuts. Torque to 31 ft. lbs.

4. Repeat on opposite side.

33963

Land Pride Skid Shoe Replacement Parts

Part No.Part Description

326-479D

SKID SHOE

802-603C

PLOW 3/8" - 16 x 1" GR5

803-198C

NUT HEX WHIZ 3/8-16 PLT

Содержание RCF3696













































































Результаты поиска

Содержание RCF3696

Отзывы:

Похожие инструкции для RCF3696

Бренды по названию

Популярные бренды

Land Pride RCF3696, Руководство оператора

Результаты поиска

Содержание RCF3696

Отзывы:

Похожие инструкции для RCF3696

Бренды по названию

Популярные бренды